| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava
Prva stran > Izpis gradiva

Izpis gradiva Pomoč

Naslov:Wear simulation of the conveyor belt transfer chute using the DEM
Avtorji:ID Lerher, Tone (Avtor)
ID Grum, Žan (Avtor)
ID Motaln, Marko (Avtor)
ID Zadravec, Matej (Avtor)
Datoteke:.pdf text23-1_673.pdf (544,47 KB)
MD5: BE80E3E721D4D29CADDB92FBD93969E2
 
URL https://www.ijsimm.com/Full_Papers/Fulltext2024/text23-1_673.pdf
 
Jezik:Angleški jezik
Vrsta gradiva:Članek v reviji
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Opis:This paper presents a wear simulation-based performance evaluation of the conveyor belt transfer chute using the DEM (Discrete Element Method). Compared to known analytical and empirical wear models, DEM simulation can significantly increase the performance of wear analysis by enabling the analysis and optimization of highly complex geometries of material handling systems such as conveyor belt transfer chutes. Only the correct design of the conveyor belt transfer chute has the potential to significantly extend its service life, resulting in considerable cost savings. Based on the parametric analysis of different angles and radius in the upper head and lower section of the transfer chute, a new geometry of the transfer chute was proposed. The wear depth of the new conveyor belt transfer chute is compared with the wear resistant and low-carbon steel of the transfer chute along with the moderate and relatively high values of the solid granules mass flow. The results show that the wear depth of the transfer chute can be significantly reduced by using the wear-resistant steel compared to the low-carbon steel, which is significantly evident in high throughput rates of the solid granules mass flow.
Ključne besede:bulk material flow, Discrete Element Method (DEM), transfer chute wear simulation, archard and relative wear, performance analysis
Status publikacije:Objavljeno
Verzija publikacije:Objavljena publikacija
Datum objave:01.03.2024
Založnik:DAAAM International Vienna
Leto izida:2024
Št. strani:str. 77-88
Številčenje:Vol. 23, no. 1
PID:20.500.12556/DKUM-91993 Novo okno
UDK:621.798:004.94
COBISS.SI-ID:188073731 Novo okno
DOI:10.2507/IJSIMM23-1-673 Novo okno
ISSN pri članku:1726-4529
Datum objave v DKUM:10.03.2025
Število ogledov:0
Število prenosov:6
Metapodatki:XML DC-XML DC-RDF
Področja:Ostalo
:
LERHER, Tone, GRUM, Žan, MOTALN, Marko in ZADRAVEC, Matej, 2024, Wear simulation of the conveyor belt transfer chute using the DEM. International journal of simulation modelling [na spletu]. 2024. Vol. 23, no. 1, p. 77–88. [Dostopano 22 april 2025]. DOI 10.2507/IJSIMM23-1-673. Pridobljeno s: https://dk.um.si/IzpisGradiva.php?lang=slv&id=91993
Kopiraj citat
  
Skupna ocena:
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
Objavi na:Bookmark and Share


Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del revije

Naslov:International journal of simulation modelling
Skrajšan naslov:Int. j. simul. model.
Založnik:DAAAM International Vienna
ISSN:1726-4529
COBISS.SI-ID:8008982 Novo okno

Licence

Licenca:CC BY-NC 4.0, Creative Commons Priznanje avtorstva-Nekomercialno 4.0 Mednarodna
Povezava:http://creativecommons.org/licenses/by-nc/4.0/deed.sl
Opis:Licenca Creative Commons, ki prepoveduje komercialno uporabo, vendar uporabniki ne rabijo upravljati materialnih avtorskih pravic na izpeljanih delih z enako licenco.

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:tok razsutega materiala, metoda diskretnih elementov, simulacija obrabe žleba za prenos, relativna obraba, analiza zmogljivosti


Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici