| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava
Prva stran > Izpis gradiva

Izpis gradiva Pomoč

Naslov:Microstructure of rapidly solidified Cu-Al-Ni shape memory alloy ribbons
Avtorji:ID Lojen, Gorazd (Avtor)
ID Anžel, Ivan (Avtor)
ID Kneissl, Albert C. (Avtor)
ID Unterweger, Elfride (Avtor)
ID Kosec, Borut (Avtor)
ID Bizjak, Milan (Avtor)
Datoteke:URL http://dx.doi.org/10.1016/j.jmatprotec.2005.02.196
 
Jezik:Angleški jezik
Vrsta gradiva:Neznano
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Opis:Cu-Al-Ni shape memory alloys (SMAs) are currently the only available high temperature SMAs, showing a good resistance against functional fatigue. In polycrystalline state, they are very brittle and exhibit, in general, only small reversible deformations. By melt spinning, thin Cu-Al-Ni ribbons can be manufactured directly from the melt. Appropriate casting parameters can ensurea single layer columnar structure with a fibre texture, which significantly increases the maximal reversible strain in longitudinal direction. Cu-Al-Ni ribbons, containing 13, 14 and 15 wt.% Al were cast by free jet melt spinning. Because of the alloys' low thermal conductivity, the cooling rate was surprisingly low - considering the crystal grain size - significantly below 103 K/s. Therefore, wide ribbons having a single layer columnar and (except the ribbons containing 13 wt.% Al) completely martensiticstructure could not be obtained. Regardless the chemical composition, the ribbons have a single layer columnar structure only if the thickness does not exceed approximately 50 m, otherwise the structure consists of at least two layers of equiaxed grains. In as-cast condition, only ribbons containing 13 wt.% Al seem to be completely martensitic. Heat treatments at temperatures up to 900 °C improved the structure of 13 and 14 wt.% Al ribbons. All ribbons exhibit one-way shape memory effect in as-cast condition. Heat-treated ribbons containing 13 wt.% Al exhibited two-way shape memory effect already after one bending and heating cycle.
Ključne besede:metallurgy, shape memory alloys, Cu-Al-Ni alloy, microstructure, melt spinning
Leto izida:2005
PID:20.500.12556/DKUM-27025 Novo okno
UDK:669.018
COBISS.SI-ID:9607190 Novo okno
ISSN pri članku:0924-0136
NUK URN:URN:SI:UM:DK:SXUPLTDV
Datum objave v DKUM:01.06.2012
Število ogledov:2526
Število prenosov:116
Metapodatki:XML DC-XML DC-RDF
Področja:Ostalo
:
LOJEN, Gorazd, ANŽEL, Ivan, KNEISSL, Albert C., UNTERWEGER, Elfride, KOSEC, Borut in BIZJAK, Milan, 2005, Microstructure of rapidly solidified Cu-Al-Ni shape memory alloy ribbons. Journal of materials processing technology [na spletu]. 2005. [Dostopano 23 marec 2025]. Pridobljeno s: http://dx.doi.org/10.1016/j.jmatprotec.2005.02.196
Kopiraj citat
  
Skupna ocena:
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
Objavi na:Bookmark and Share


Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del revije

Naslov:Journal of materials processing technology
Skrajšan naslov:J. mater. process. technol.
Založnik:Elsevier
ISSN:0924-0136
COBISS.SI-ID:30105600 Novo okno

Sekundarni jezik

Jezik:Angleški jezik
Ključne besede:metalurgija, zlitine z oblikovnim spominom, zlitina Cu-Al-Ni, mikrostruktura


Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici