| Naslov: | Kraft lignin/tannin as a potential accelerator of antioxidant and antibacterial properties in an active thermoplastic polyester-based multifunctional material |
|---|
| Avtorji: | ID Pušnik Črešnar, Klementina (Avtor)
ID Zamboulis, Alexandra (Avtor)
ID Bikiaris, Dimitrios (Avtor)
ID Aulova, Alexandra (Avtor)
ID Fras Zemljič, Lidija (Avtor) |
|---|
| Datoteke: |  Kraft_Lignin_Tannin_as_a_Potentia-Cresnar-2022.pdf (3,87 MB)
MD5: C2A94CE5A61CFA85C422135DBB2E0A39
 https://www.mdpi.com/2073-4360/14/8/1532
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Znanstveno delo |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | This research focuses on key priorities in the field of sustainable plastic composites that will lead to a reduction in CO2 pollution and support the EU’s goal of becoming carbon neutral by 2050. The main challenge is to develop high-performance polyphenol-reinforced thermoplastic composites, where the use of natural fillers replaces the usual chemical additives with non-toxic ones, not only to improve the final performance but also to increase the desired multifunctionalities (structural, antioxidant, and antibacterial). Therefore, poly (lactic acid) (PLA) composites based on Kraft lignin (KL) and tannin (TANN) were investigated. Two series of PLA composites, PLA-KL and PLA-TANN, which contained natural fillers (0.5%, 1.0%, and 2.5% (w/w)) were prepared by hot melt extrusion. The effects of KL and TANN on the PLA matrices were investigated, especially the surface physicochemical properties, mechanical properties, and antioxidant/antimicrobial activity. The surface physicochemical properties were evaluated by measuring the contact angle (CA), roughness, zeta potential, and nanoindentation. The results of the water contact angle showed that neither KL nor TANN caused a significant change in the wettability, but only a slight increase in the hydrophilicity of the PLA composites. The filler loading, the size of the particles with their available functional groups on the surfaces of the PLA composites, and the interaction between the filler and the PLA polymer depend on the roughness and zeta potential behavior of the PLA-KL and PLA-TANN composites and ultimately improve the surface mechanical properties. The antioxidant properties of the PLA-KL and PLA-TANN composites were determined using the DPPH (2,2′-diphenyl-1-picrylhydrazyl) test. The results show an efficient antioxidant behavior of all PLA-KL and PLA-TANN composites, which increases with the filler content. Finally, the KL- and PLA-based TANN have shown resistance to the Gram-negative bacteria, E. coli, but without a correlation trend between polyphenol filler content and structure. |
|---|
| Ključne besede: | poly (lactic acid), Kraft lignin, tannin, multifunctionality of PLA composites, surface mechanical properties, antioxidant/antibacterial activity |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 03.03.2022 |
|---|
| Datum sprejetja članka: | 31.03.2022 |
|---|
| Datum objave: | 09.04.2022 |
|---|
| Založnik: | MDPI |
|---|
| Leto izida: | 2022 |
|---|
| Št. strani: | 18 str. |
|---|
| Številčenje: | Letn. 14, Št. 8, št. članka 1532 |
|---|
| PID: | 20.500.12556/DKUM-85902  |
|---|
| UDK: | 677.017:539.2 |
|---|
| COBISS.SI-ID: | 104505603 |
|---|
| DOI: | 10.3390/polym14081532 |
|---|
| ISSN pri članku: | 2073-4360 |
|---|
| Avtorske pravice: | © 2022 by the authors |
|---|
| Datum objave v DKUM: | 18.09.2023 |
|---|
| Število ogledov: | 495 |
|---|
| Število prenosov: | 193 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
