| | SLO | ENG | Cookies and privacy

Bigger font | Smaller font

Show document

Title:Konstruiranje pridržalne čeljusti za sistem odpiranja napihovalnega tulca Roll-Bond plošče za HPO3
Authors:ID Sklepič, Amadej (Author)
ID Kaljun, Jasmin (Mentor) More about this mentor... New window
ID Cupar, Andrej (Co-mentor)
Files:.pdf VS_Sklepic_Amadej_2017.pdf (1,88 MB)
MD5: 7E190A31527BD25B4082AF3001CA8596
 
Language:Slovenian
Work type:Bachelor thesis/paper (mb11)
Typology:2.11 - Undergraduate Thesis
Organization:FS - Faculty of Mechanical Engineering
Abstract:Za temo diplomskega dela, smo se dogovorili v podjetju Talum IZPARILNIKI d.o.o., kjer sem opravljal praktično usposabljanje. V diplomski nalogi je predstavljeno konstruiranje pridrževalnih čeljusti, s pridržalno enoto, za sistem odpiranja napihovalnega tulca Roll-Bond plošče za stroj HPO3. Razlog za izdelavo novih čeljusti, je v obstoječih čeljustih, ki nimajo ustrezne zatesnitve, prav tako pa se težko prilagajajo na različne debeline Roll-Bond plošč. Želja je bila konstruirati in izdelati nove čeljusti, ki bodo zmanjšale izmet in morebitna servisna dela. V uvodu je opisana družba Talum in podjetje Talum IZPARILNIKI d.o.o. in njihovi produkti. Nato je opisan problem, ki se je pojavljal do sedaj in rešitev dosedanjega problema. Po dogovoru s sodelavci o novi rešitvi, je sledilo 3D modeliranje čeljusti s pridržalno enoto. Predstavljena je tudi izdelava in montaža končnega izdelka.
Keywords:konstruiranje, čeljust, Roll-Bond, izparilnik, HPO3
Year of publishing:2017
Publisher:[A. Sklepič]
Source:Maribor
PID:20.500.12556/DKUM-65044 New window
UDC:621.838.21-11(043.2)
COBISS.SI-ID:20519446 New window
NUK URN:URN:SI:UM:DK:DULILCZX
Publication date in DKUM:28.02.2017
Views:1184
Downloads:120
Metadata:XML RDF-CHPDL DC-XML DC-RDF
Categories:KTFMB - FS
:
Kopiraj citat
  
Average score:(0 votes)
Your score:Voting is allowed only for logged in users.
Share:AddThis
AddThis uses cookies that require your consent. Edit consent...

Hover the mouse pointer over a document title to show the abstract or click on the title to get all document metadata.

Secondary language

Language:English
Title:Design of a blank holder jaw for the opening system of the inflation tube Roll-Bond plate for HPO3
Abstract:The topic of the thesis, we have agreed in the company Talum IZPARILNIKI d.o.o., where I performed practical training. The thesis presents the design of a holding jaw, with a holding system, for the opening system of an inflation tube of a Roll-Bond plate for the machine HPO3. The reason for producing the new jaw is, because the existing jaw does not have adequate sealing, and also it is difficult to adapt to the different thickness of the Roll-Bond plates. The desire was to construct and produce a new jaw that will reduce the ejection and possible repair work. The introduction describes the firm Talum and the company Talum IZPARILNIKI d.o.o. and their products. Then the problem that has occurred to date is described and also its current solution. The agreement with the staff for the new solution, was followed by a 3D of modeling the jaw with a holding unit. Also presented is the manufacture and installation of the finished product.
Keywords:construction, jaw, Roll-Bond evaporator, HPO3


Comments

Leave comment

You must log in to leave a comment.

Comments (0)
0 - 0 / 0
 
There are no comments!

Back
Logos of partners University of Maribor University of Ljubljana University of Primorska University of Nova Gorica