| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Izpis gradiva

Naslov:Workloads and standard time norms in garment engineering
Avtorji:Dragičević, Zvonko (Avtor)
Zavec Pavlinič, Daniela (Avtor)
Geršak, Jelka (Avtor)
Datoteke:URL http://www.tx.ncsu.edu/jtatm
 
Jezik:Angleški jezik
Vrsta gradiva:Neznano ()
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Opis:Posibilities of new methods for measuring loading and standard time norms are presented, as applied in the field of garment engineering. Measurements deescribed are performed on modern measuring equipment designed to measure and perform computer analysis of temporal values of processing parameters in sewing operation and simultaneously record in two planes using a video system. The measuring system described was used to investigate sewing operation for the seam on a ladies' fashion suit, 52 cm long. For the operation investigated, method of work employing the MTM (Methods Time Measurements) system with analysis of basic movements was selected. The MTM system used shows that normal time for the operation in question is around 429.3 TMU (15.5 s). Investigations of workload imposed on the worker according to the OADM method were done simultaneously, and total ergonomic loading coefficients of Ker=0.082 was established, thus determining the time necessary to organise the process of work as 464.5 TMU (16.7 s). Simultaneous measurements of time and dynamic changes of processing parameters, as well as logical sets of movements, are important for defining favourable operation structures, time norms ergonomically designed systems of work and workplaces in garment engineering, as early as in the phase of designing operation. The investigations described make possible to find optimal distribution of working elements and zones of reach important for ergonomic designing and/or re-designing of workplaces, which results in considerably reduced level of fatigue in work optimal quality level, higher degree of utilisation of equipment installed and lower manufacturing costs.
Ključne besede:garment engineering, sewing, standard time norms, norms, time study, work study, MTM, motion timestudy measurement
Leto izida:2002
UDK:687:658.516
COBISS_ID:7241750 Povezava se odpre v novem oknu
ISSN pri članku:1533-0915
NUK URN:URN:SI:UM:DK:A4UXRVQZ
Število ogledov:941
Število prenosov:29
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
Področja:Ostalo
:
  
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del revije

Naslov:Journal of textile and apparel technology and management
Založnik:Dept. of Textile and Apparel Technology and Management
ISSN:1533-0915
COBISS.SI-ID:7240982 Novo okno

Sekundarni jezik

Jezik:Angleški jezik
Ključne besede:konfekcija, oblačilno inženirstvo, časi izdelave, šivanje, norme, študij časa, študij dela, MTM


Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici