| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Izpis gradiva

Naslov:Basic solutions on shape complexity evaluation of STL data
Avtorji:ID Valentan, Bogdan (Avtor)
ID Brajlih, Tomaž (Avtor)
ID Drstvenšek, Igor (Avtor)
ID Balič, Jože (Avtor)
Datoteke:URL http://157.158.19.167/papers_vol26_1/2619.pdf
 
Jezik:Angleški jezik
Vrsta gradiva:Neznano ()
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Opis:Purpose of this paper is to present basic solutions on shape complexity, based on basic information of the STL data. Design/methodology/approach: Paper presents a few methods of mathematically evaluating the complexity of the shape. Methods vary from very simple based on the number of triangles in STL file, STL file size and the parts volume, to the more complex mathematical evaluation based on the basic relations of the STL data. Findings: We discovered that evaluation of shape complexity based only on basic data of STL data gives us some basic results on part complexity and can be used for further researches. Research limitations/implications: For parts with large block volume/part volume ratio and thinner parts with free form surfaces only the first method is suitable and gives suitable results. Practical implications: In a rapidly developing field of manufacturing technologies choosing the optimal manufacturing procedure is a difficult and crucial decision. Usually the decision is based on experience evaluation that is fast and can be optimal. Usually, this method produces goods results, but in some cases this method can lead to cost increases and reduced economic efficiency without us even knowing that. Therefore, it is crucial, that a fast and simple solution is developed, by which the optimal way of manufacturing can be determined. Originality/value: Choosing maximum efficient manufacturing processes on base of part complexity is a new perspective in manufacturing, which, properly evolved and complied can cause revolution in manufacturing optimization, especially in hybrid manufacturing processes.
Ključne besede:manufacturing systems, shape complexity, complex shapes, manufacturing optimization, engineering design, STL files, STL file parameters
Leto izida:2008
PID:20.500.12556/DKUM-27409 Novo okno
UDK:621.9:004.89
COBISS.SI-ID:12022550 Novo okno
ISSN pri članku:1734-8412
NUK URN:URN:SI:UM:DK:JKREU6Y6
Datum objave v DKUM:01.06.2012
Število ogledov:1706
Število prenosov:59
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
Področja:Ostalo
:
Kopiraj citat
  
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del revije

Naslov:Journal of achievements in materials and manufacturing engineering
Skrajšan naslov:J. achiev. mater. manuf. eng.
Založnik:International OCSCO World Press
ISSN:1734-8412
COBISS.SI-ID:10509078 Novo okno

Sekundarni jezik

Jezik:Angleški jezik
Ključne besede:proizvodni sistemi, ocena zahtevnosti oblike, kompleksne oblike, optimiranje izdelave, inženirsko načrtovanje, STL datoteke, parametri STL datotek


Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici