| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 4 / 4
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Application of semantic technology for calculation of welding time in the development of new products
Ambrož Stropnik, Tomaž Vuherer, Ivan Samardžić, Milan Zorman, 2017, izvirni znanstveni članek

Opis: Determining the time of execution is very important in the early stages of each project (e.g. making offers, design phase etc.), especially in the stage of planning. This paper presents our approach to estimating the welding time for the purposes of planning the manufacturing processes. The approach is based on the knowledge of welding experts from the Nieros metal d.o.o. company and standards of welding (international and internal). An expert system was developed based on semantic web technologies for calculating the welding time in the product design phase and it is strongly integrated with the main ERP system of the Nieros metal d.o.o. company. Test results are presented at the end of this article.
Ključne besede: expert systems, new product development, ontology, welding of steels
Objavljeno: 23.08.2017; Ogledov: 544; Prenosov: 322
.pdf Celotno besedilo (1,16 MB)
Gradivo ima več datotek! Več...

2.
Weld joint fracture behaviour of HSLA steels dissimilar in strength
Inoslav Rak, Arpad Treiber, 1998, izvirni znanstveni članek

Opis: The effect of strength differences (mismatch) between weld metal and two base metals as well as local variations of strength within weld metal/HAZ zones on the toughness properties were discussed. The significance of local fracture toughness measurement technique was also discussed by comparing the CTOD results of [delta]5 and British Standard [delta]BS. Some differences between the two techniqes were discussed in particular for CGHAZ toughness of similar and dissimilar joints.
Ključne besede: welding, welded joints, fracture mechanics, HSLA steels, fracture toughness
Objavljeno: 10.07.2015; Ogledov: 843; Prenosov: 24
URL Povezava na celotno besedilo

3.
Vloga in nastanek mikrostrukturnih sestavin M-A v zvarnih spojih maloogljičnih visokotrdnostnih konstrukcijskih jekel
Zdravko Praunseis, Masao Toyoda, Alojz Križman, Mitsuru Ohata, 2001, pregledni znanstveni članek

Opis: The existence of martensite-austenite constituents in the weld metal and heat-affected zone seriously reduces the fracture toughness of the welded joint. Therefore, we have investigated the formation of the martensite-austenite constituents when high-strength low-alloy steel is welded with a high heat input or using multi-pass welding. This paper deals with the effects of martensite-austenite constituents on the fracture toughness, the metallurgical features of the martensite-austenite constituents, and the prevention and elimination of the martensite-austenite constituents in the welded joints.
Ključne besede: arc welding, high-strength low-alloy steels, microstructure, martensite-austenite constituents, weld metal, heat-affected zone, cooling rate
Objavljeno: 01.06.2012; Ogledov: 1430; Prenosov: 89
.pdf Celotno besedilo (985,12 KB)
Gradivo ima več datotek! Več...

4.
The fracture behaviour of global/local mis-matched weld joints provided on HSLA steels
Inoslav Rak, Nenad Gubeljak, Zdravko Praunseis, 2001, izvirni znanstveni članek

Opis: The fracture behaviour of thick section high strength steel weldments, that contain soft root passes, has been studied. Two different weld consumables with different strength mismatch (1>M>1) and fracture toughness properties in the WM have significantly increased the complexity of the mis-match effect and failure behaviour of weld joints, depending on the crack location and the thickness of the soft root layer. The aim was to explain the effect of strength heterogeneity between BM and WM and between different regions in WM (global/local mismatching). R-curves of WM and HAZ regions were also discussed. The conclusion is that the application of a welding procedure with a two-pass soft root layer, introduced for the purpose of reducing or even omitting preheating, can be recommended in mis-matched weld joints on steel grade HT80. Nevertheless, the alloying from BM, and the tempering effect of subsequent weld passes, have to be taken into account. They can cause reduction of the root region ductility and affect the local mismatch in WM and HAZ. The deterioration by providing a soft root layer can probably be reduced by a selected consumable and proper welding procedure. The final conclusion is that the application of a mismatched weld joint with a soft root layer can be recommended only if high root toughness can be provided.
Ključne besede: welding, welded joints, strength mismatching, fracture toughness, CTOD, hardness, impact toughness, HSLA steels
Objavljeno: 01.06.2012; Ogledov: 1471; Prenosov: 101
.pdf Celotno besedilo (441,77 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.1 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici