Iskanje po katalogu digitalne knjižnice

Opis: This paper studies the load-bearing capacity of various concrete tetrapods under quasistatic loading. The tetrapods were made of plain concrete and synthetic-polymer-fiber-reinforced concrete. Load tests of the tetrapods were performed. The maximum load-bearing capacity and the residual-load-bearing capacity of the tetrapods (the load-bearing capacity after the first crack or at different crack widths) were evaluated. The strength and residual-strength values were backcalculated from the load-bearing capacities, and compared with available data from the literature. The specimens with and without fibers achieved similar maximum load-bearing capacities, with cracks occurring at identical locations. However, the differences in residual-load-bearing capacity were more significant. The synthetic-polymer-fiber-reinforced concrete tetrapods exhibited relatively high residual-load-bearing capacities, even at higher displacements and crack widths. Two different calculation-procedures were used for the load-bearing-capacity evaluation. A load-displacement calculation based on the moment-versus-curvature relation and the plastic-hinge approach was performed, and additionally proved the applicability of the employed calculation-procedures for the concrete tetrapod load-bearing-capacity evaluation.
Ključne besede: tetrapods, concrete, synthetic-polymer fibers, load tests, load-bearing capacity, residual load-bearing capacity, load displacement, calculation
Objavljeno v DKUM: 12.03.2025; Ogledov: 0; Prenosov: 1
Celotno besedilo (5,75 MB)
Gradivo ima več datotek! Več...

Opis: The behaviour of horizontal floor diaphragms plays a crucial role in ensuring the overall response of a building during earthquakes, as the stiffness of these diaphragms determines whether the structure will act as an integrated system. If the diaphragms do not exhibit sufficient stiffness, differences in the redistribution of forces on wall elements arise, increasing the risk of significant deformations and even local damage, which is commonly observed in earthquake-affected areas. Additionally, flexible diaphragms heighten the risk of torsional effects. Due to these factors, more attention should be given to the response of buildings with flexible diaphragms. Eurocode standard specifies general requirements under which diaphragms should be considered rigid within their plane, depending on the maximum diaphragm moment. However, specific guidelines regarding the geometric and material properties of elements that significantly impact seismic behaviour are not included in the existing European standards. This served as a basis for conducting a numerical study analysing the in-plane behaviour of floor elements made from different materials. This study, limited to a simple box-shaped structure with masonry walls, symmetrical in both orthogonal directions, evaluated and thoroughly analysed the deformations for different types of diaphragms, including prefabricated wooden frame-panel floors, CLT panels, and reinforced concrete slabs. Special emphasis was placed on wooden structural elements due to the increased demand for timber construction, as the behaviour of these elements needs to be properly studied, especially in seismic regions. The study results were obtained through FEM analysis using the SCIA Engineer software, version 22. The modelling of elements was carried out considering the orthotropy of brick wall and wooden ceiling elements, as well as simulating the appropriate shear stiffness of the connecting means.
Ključne besede: horizontal diaphragms, floor flexibility, lateral load resisting system, timber frame-panel floor, cross-laminated timber, concrete slab, seismic design
Objavljeno v DKUM: 10.01.2025; Ogledov: 0; Prenosov: 16
Celotno besedilo (8,44 MB)
Gradivo ima več datotek! Več...

Opis: Purpose – Ready-mix concrete delivery problem (RMCDP), a specific version of the vehicle routing problem (VRP), is a relevant supply-chain engineering task for construction management with various formulations and solving methods. This problem can range from a simple scenario involving one source, one material and one destination to a more challenging and complex case involving multiple sources, multiple materials and multiple destinations. This paper presents an Internet of Things (IoT)-supported active building information modeling (BIM) system for optimized multi-project ready-mix concrete (RMC) delivery. Design/methodology/approach – The presented system is BIM-based, IoT supported, dynamic and automatic input/output exchange to provide an optimal delivery program for multi-project ready-mix-concrete problem. The input parameters are extracted as real-time map-supported IoT data and transferred to the system via an application programming interface (API) into a mixed-integer linear programming (MILP) optimization model developed to perform the optimization. The obtained optimization results are further integrated into BIM by conventional project management tools. To demonstrate the features of the suggested system, an RMCDP example was applied to solve that included four building sites, seven eligible concrete plants and three necessary RMC mixtures. Findings – The system provides the optimum delivery schedule for multiple RMCs to multiple construction sites, as well as the optimum RMC quantities to be delivered, the quantities from each concrete plant that must be supplied, the best delivery routes, the optimum execution times for each construction site, and the total minimal costs, while also assuring the dynamic transfer of the optimized results back into the portfolio of multiple BIM projects. The system can generate as many solutions as needed by updating the real-time input parameters in terms of change of the routes, unit prices and availability of concrete plants. Originality/value – The suggested system allows dynamic adjustments during the optimization process, andis adaptable to changes in input data also considering the real-time input data. The system is based on spreadsheets, which are widely used and common tool that most stakeholders already utilize daily, while also providing the possibility to apply a more specialized tool. Based on this, the RMCDP can be solved using both conventional and advanced optimization software, enabling the system to handle even large-scale tasks as necessary.
Ključne besede: active building information modeling, BIM, internet of things, IoT, multi-project environment, optimization, ready-mix-concrete delivery, RMC
Objavljeno v DKUM: 11.09.2024; Ogledov: 32; Prenosov: 9
Celotno besedilo (3,94 MB)
Gradivo ima več datotek! Več...

Opis: A nonlinear semi-numeric and finite element analysis of three-point bending tests of notched polymer fiber-reinforced concrete prisms was performed. The computational and experimental results were compared in terms of the load-displacement behavior. The vertical midspan displacement and the crack mouth opening displacement results were considered. The nonlinear semi-numeric computational procedure involved the moment-curvature relation, calculated by considering the constitutive material law from the fib Model Code for Concrete Structures 2010, and considered a plastic hinge mechanism to simulate the cracked region behavior. Two sets of tensile mechanical properties were considered for the constitutive material law: back-calculated (by an inverse analysis) tensile strength properties from the experimental results, and tensile strength properties calculated by simplified expressions from the fib Model Code for Concrete Structures 2010. Other mechanical properties were determined by additional compressive tests and standard relations for the dependency of various mechanical properties on the concrete compressive strength. The nonlinear finite element analysis incorporated the Menetrey-Willam material model to simulate the fiber-reinforced concrete behavior. The nonlinear semi-numeric analysis load-displacement results based on the back-calculated tensile strength properties relatively accurately matched with the experimental results, whereas the nonlinear semi-numeric analysis load-displacement results based on tensile strength properties calculated by simplified expressions from the fib Model Code for Concrete Structures 2010 and the nonlinear finite element analysis load-displacement results showed certain shortcomings.
Ključne besede: polymer fiber-reinforced concrete, moment-curvature relation, nonlinear plastic hinge, load-displacement relation, crack width, nonlinear analysis, finite element analysis, Menetrey-Willam material model, three-point bending test, compressive test
Objavljeno v DKUM: 19.02.2024; Ogledov: 350; Prenosov: 29
Celotno besedilo (6,91 MB)
Gradivo ima več datotek! Več...

Opis: X-section cast-in-place concrete (XCC) piles are used because they have a higher bearing capacity than circularsection cast-in-place concrete (CCC) piles of the same cross-sectional area. Although the bearing capacity of XCC piles has been studied, the performance of XCC single piles, especially for the stress-transfer mechanism dependent on the geometrical effects, is still not fully understood. This paper reports two comparative field static load tests on an XCC and a CCC single pile of the same cross-sectional area. In addition, corresponding threedimensional numerical back-analyses are performed to provide a fundamental understanding. The measured and computed results reveal that the XCC single pile has an approximately 25% higher ultimate bearing capacity than the CCC single pile. This is because the XCC single pile has an approximately 20% larger total side resistance, which is caused by a 60% larger pile perimeter and a slightly smaller unit side resistance. Lateral soil arching effects are developed, causing a non-uniform effective normal stress and a shear stress across the circumference of the XCC single pile. It is suggested that XCC single piles have a higher efficiency in terms of material saving compared with CCC single piles.
Ključne besede: X-section cast-in-place concrete pile, field static load test, three-dimensional numerical back-analysis, stresstransfer mechanism, side resistance, soil arching
Objavljeno v DKUM: 15.06.2018; Ogledov: 1462; Prenosov: 185
Celotno besedilo (485,57 KB)
Gradivo ima več datotek! Več...