| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 5 / 5
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Assembly line optimization using MTM time standard and simulation modeling—A case study
Matic Breznik, Borut Buchmeister, Nataša Vujica-Herzog, 2023, izvirni znanstveni članek

Opis: This study presents an approach to solving the assembly line balancing problem (ALBP) using the Methods-Time Measurement (MTM) time standard and simulation software. ALBP is a common problem in manufacturing where a set of tasks with fixed times must be assigned to a series of sequential workstations in order to minimize the total idle time and reduce the assembly cost per product. This study uses MTM, a widely used production process scheduling method, to create a new time analysis of an assembly process that was previously balanced using the Work-Factor method and time study. This literature review shows that there are a lack of combinations of updated time analyses with newer simulation approaches in the current literature, and this was the motivation for the present work. An assembly line simulation was performed using Simio software to evaluate different design options and operating scenarios. The results show that the use of MTM and simulation can help minimize idle time and improve assembly line performance, thereby reducing costs and increasing efficiency. This study shows that the approach of using MTM and simulation is effective in solving ALBP and is a useful tool for manufacturing companies to improve the performance of their assembly lines and reduce costs.
Ključne besede: optimization, production planning, assembly line, MTM time standard, simulation, industry 4.0
Objavljeno v DKUM: 23.05.2023; Ogledov: 460; Prenosov: 70
.pdf Celotno besedilo (3,25 MB)
Gradivo ima več datotek! Več...

2.
Material and energy balance in the planning of production costs
Manuela Ingaldi, Dorota Klimecka-Tatar, 2016, samostojni znanstveni sestavek ali poglavje v monografski publikaciji

Ključne besede: material, energy, manufacturing system model, production costs, planning
Objavljeno v DKUM: 11.05.2018; Ogledov: 1515; Prenosov: 92
.pdf Celotno besedilo (1,03 MB)
Gradivo ima več datotek! Več...

3.
A new method for determining extra time by considering ergonomic loads in the garment and metal working industries
Vekoslav Verhovnik, Andrej Polajnar, 1993, izvirni znanstveni članek

Opis: The changing labour conditions in the garment and metal-working industries have led to the necessity of determining new extra times to establish the time standard. In this paper, a method of measuring stress and strain imposed upon the operator in new working conditions by determining the additional production coefficient is presented. The method gives criteria and grades to assess stress at the workplace. Physical stress (dynamic and static), thermal and visual stress, discomfort caused by noise, aerosols, gases and vapours, and the stress due to monotony are assessed. The stresses are expressed by ecological, physiological and psychological indexes. The indexes are pondered. Ponderation includes the factor of the magnitude and the time of exposure to stress. Ponderation is expressed by the number of points, the total being an adequate presentation of the stresses. Stress and strain decrease the working performance of the operator. Therefore they must be included in the standard to compensate for the operator's lower working efficiency due to physical and psychological strain at the workplace, Short breaks and stops allowed during work enable the operator to perform work tasks without getting excessively tired. The necessary correction of the production time is made by applying the ergonomic coefficient Ker.
Ključne besede: job analysis, production planning, stress assessment, time study, working conditions, working environment
Objavljeno v DKUM: 30.03.2017; Ogledov: 1166; Prenosov: 164
.pdf Celotno besedilo (7,13 MB)
Gradivo ima več datotek! Več...

4.
A model of simulation environment for prediction and optimisation of production processes
Igor Drstvenšek, Mirko Ficko, Ivo Pahole, Jože Balič, 2004, izvirni znanstveni članek

Opis: Paper describes means and methods for computer based optimisation of production processes using a new approach based on technological database (TDB) with genetic algorithm incorporated into a database management system (DBMS). The TDB serves as a store of tools and machine tools from which they can be assigned to different work operations. Work operations are basic entities of orders placed into queues. The goal of the model is to find available resources from the TDB in order to empty the queue in shortest time with lowest costs. To this purpose the model consist the technological database whose DBMS includes a genetic algorithm based optimiser. It checks the orders queue and searches for appropriate combinations of tools and machine tools from the TDB, which can be combined into needed work operations. It also performs an optimisation of time and costs according to so called static parameters of tools and machine tools.
Ključne besede: production processes, simulation, process planning, technological databases, genetic algorithms
Objavljeno v DKUM: 01.06.2012; Ogledov: 1816; Prenosov: 102
URL Povezava na celotno besedilo

5.
Iskanje izvedeno v 1.35 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici