1. Using neural networks in the process of calibrating the microsimulation models in the analysis and design of roundabouts in urban areasIrena Ištoka Otković, 2011, doktorska disertacija Opis: The thesis researches the application of neural networks in computer program calibration of traffic micro-simulation models. The calibration process is designed on the basis of the VISSIM micro-simulation model of local urban roundabouts.
From the five analyzed methods of computer program calibration, Methods I, II and V were selected for a more detailed research. The three chosen calibration methods varied the number of outgoing traffic indicators predicted by neural networks and a number of neural networks in the computer program calibration procedure. Within the calibration program, the task of neural networks was to predict the output of VISSIM simulations for selected functional traffic parameters - traveling time between the measurement points and queue parameters (maximum queue and number of stopping at the roundabout entrance). The Databases for neural network training consisted of 1379 combinations of input parameters whereas the number of output indicators of VISSIM simulations was varied. The neural networks (176 of them) were trained and compared for the calibration process according to training and generalization criteria. The best neural network for each calibration method was chosen by using the two-phase validation of neural networks.
The Method I is the calibration method based on calibration of a traffic indicator -traveling time and it enables validation related to the second observed indicator – queue parameters. Methods II and V connect the previously described calibration and validation procedures in one calibration process which calibrates input parameters according to two traffic indicators.
Validation of the analyzed calibration methods was performed on three new sets of measured data - two sets at the same roundabout and one set on another location. The best results in validation of computer program calibration were achieved by the Method I which is the recommended method for computer program calibration.
The modeling results of selected traffic parameters obtained by calibrated VISSIM traffic model were compared with: values obtained by measurements in the field, the existing analysis methods of operational roundabouts characteristics (Lausanne method, Kimber-Hollis, HCM) and modeling by the uncalibrated VISSIM model. The calibrated model shows good correspondence with measured values in real traffic conditions. The efficiency of the calibration process was confirmed by comparing the measured and modeled values of delays, of an independent traffic indicator that was not used in the process of calibration and validation of traffic micro-simulation models.
There is also an example of using the calibrated model in the impact analysis of pedestrian flows on conflicting input and output flows of vehicles in the roundabout. Different traffic scenarios were analyzed in the real and anticipated traffic conditions. Ključne besede: traffic models, traffic micro-simulation, calibration of the VISSIM model, computer program calibration method, neural networks in the calibration process, micro-simulation of roundabouts, traffic modeling parameters, driving time, queue parameters, delay Objavljeno: 02.06.2011; Ogledov: 3591; Prenosov: 245 Celotno besedilo (13,21 MB) |
2. Analysis of growth models for batch kefir grain biomass production in RC1 reaction systemMarko Tramšek, Andreja Goršek, 2008, izvirni znanstveni članek Opis: This work describes the statistical analysis of three mathematical models, modified for describing the kefir grain biomass growth curve. Experimental data of time-dependent kefir grain mass increase were used. The propagation was performed in RC1 batch reaction system under optimal bioprocess parameters (temperature, rotational frequency of stirrer, glucose mass concentration) using traditional cultivation in fresh, high-temperature, pasteurized whole fat cow's milk. We compared values of biological parameters obtained by applying the nonlinear regression of experimental data in logistic, Gompertz and Richards models. The most statistically appropriate model was determined using the seven statistical indicators. We established that the kefir grain biomass growth curve during batch propagation under optimal bioprocess conditions can be most successfully described using the Gompertz growth model. Ključne besede: chemical processing, milk products, kefir grain growth, process parameters, design of experiments, modeling, mathematical models, Gompertz growth model, RC1 Objavljeno: 31.05.2012; Ogledov: 1756; Prenosov: 60 Povezava na celotno besedilo |
3. The aerobic biodegradation kinetics of plant tannins in industrial wastewaterMarko Tramšek, Andreja Goršek, Peter Glavič, 2006, izvirni znanstveni članek Opis: This paper describes an experimental determination of the biodegradation rate for tannins present in industrial wastewater, after the extraction of chestnut chips. Experiments were performed in a laboratory aerobic reactor (Armfield) by using biomass from an existing industrial wastewater treatment plant. The outlet tannins concentration was determined under various processing conditions. Simultaneously, an optical microscope was used to monitor the mix of microbiological cultures in the biomass. On the basis of data obtained in experiments, non-linear regression was used to perform parametric analysis of various kinetic models, which took into account inhibition, as quoted in literature (Haldane, Edwards, Aiba, Luong). The statistical analysis, based on the P-criterion, F-criterion, adjusted coefficient of determination, Kolmogorov-Smirnov test and root mean squared error, showed that the biodegradation of plant tannins in industrial wastewater under selected conditions for aerobic digestion, can be most successfully described statistically by the Aiba's kinetic model. Ključne besede: plant tannins, susbtrate inhibition, kinetic models, statistic analysis, aerobic industrial wastewater digestion Objavljeno: 31.05.2012; Ogledov: 1022; Prenosov: 20 Povezava na celotno besedilo |
4. |
5. Different Higgs models and the number of Higgs particlesLeila Marek-Crnjac, 2006, izvirni znanstveni članek Opis: In this short paper we discuss some interesting Higgs models. It is concluded that the most likely scheme for the Higgs particles consists of five physical Higgs particles. These are two charged H▫$^+$▫, H▫$^-$▫ and three neutrals ▫$h^0$▫, H▫$^0$▫, A▫$^0$▫. Further more the most probably total number of elementary particles for each model is calculated [El Naschie MS. Experimental and theoretical arguments for the number of the mass of the Higgs particles. Chaos, Solitons & Fractals 2005;23:1091-8; El Naschie MS. Determining the mass of the Higgs and the electroweak bosons. Chaos, Solitons & Fractals 2005;24:899-905; El Naschie MS.On 366 kissing spheres in 10 dimensions, 528 P-Brane states in 11 dimensions and the 60 elementary particles of the standard model. Chaos, Solitons & Fractals 2005;24:447-57]. Ključne besede: mathematics, Higgs models, Higgs particles, Riemann tensor, Killing vector, minimal super symmetric standard model Objavljeno: 30.05.2012; Ogledov: 1654; Prenosov: 37 Povezava na celotno besedilo |
6. Analytical calculation of diffusion coefficients and other transport properties in binary mixturesJurij Avsec, Maks Oblak, 2006, izvirni znanstveni članek Opis: The note features the mathematical model of computing binary diffusion coefficient, thermal diffusion factor and viscosity in the real-gas region on the basis of nonequilibrium statistical mechanics. For the analytical calculation of transport properties, we have used the Kihara and Chapman-Cowling model up to the third order. In the presented note we calculated transport properties for mixtures between carbon monoxide and helium. We have developed the new mixing rules for the calculation of transport properties for mixtures. The analytical results obtained by statistical mechanics are compared with the experimental data and they show relatively good agreement. Ključne besede: thermodynamics, statistical thermodynamics, mathematical models, binary diffusion coefficient, thermal diffusivity, binary mixtures Objavljeno: 30.05.2012; Ogledov: 1182; Prenosov: 29 Povezava na celotno besedilo |
7. Combustion simulation in the secondary chamber of a pilot-scale incineratorNiko Samec, Filip Kokalj, Jyh-Yan Chen, 2007, izvirni znanstveni članek Opis: A numerical analysis of combustion in the secondary chamber (thermoreactor) ofa two-stage pilot scale incinerator using computational fluid dynamics (CFD)is presented in detail. Various versions of the CFD program package CFX were used, which offer different combustion models for specific types and forms of combustion processes. The present study was focused on those physicalconditions that assure complete combustion, that is, temperature, residence time, and turbulent mixing. The selection of an appropriate combustion model was based on a comparison of the numerical results and experimental values of some combustion macro parameters in a thermoreactor. Combustion models based on one-step bimolecular chemical reaction and models based on multistep reactions were used. These models enabled a more detailed prediction of the combustion process in the secondary chamber of a pilot-scaleincinerator. The products of incomplete combustion that are significantly important for the designing and optimization of combustion devices can be predicted by applying multistep reaction models more accurately, especially in a transient regime of combustion. Ključne besede: waste incineration, numerical modeling, combustion models, incinerator chamber, CFX, CFD, computational fluid dynamics Objavljeno: 31.05.2012; Ogledov: 1291; Prenosov: 36 Povezava na celotno besedilo |
8. Core technological, marketing and complementary competencies as determinants of innovative performance : ph.d. dissertationTanja Rajkovič, 2009, doktorska disertacija Ključne besede: industrial enterprises, innovations, technology, competence, competition, competitive advantage, market, models, analysis Objavljeno: 30.05.2012; Ogledov: 1341; Prenosov: 47 Povezava na celotno besedilo |
9. |
10. Feature extraction from CAD model for milling strategy predictionJože Balič, Simon Klančnik, Simon Brezovnik, 2008, izvirni znanstveni članek Opis: In this paper we present a procedure of feature determination from a CAD model. From the model we extract information, which has the greatest influence on the technological parameters of treatment and then transform this information into appropriate input data for different intelligent processing strategy prediction systems (for example artificial neural network). With formally complex CAD models, different processing strategies are required on a single workpiece. For this reason we use segmentation as described in this paper, to partition the surface of the CAD model into regions, so that we treat each region as an independent model and determine its features. Ključne besede: CAD-CAM systems, milling strategies, feature extraction, CAD models, segmentation Objavljeno: 31.05.2012; Ogledov: 1189; Prenosov: 22 Povezava na celotno besedilo |