| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 2 / 2
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Study of ▫$Ni/Y_2O_3/polylactic$▫ acid composite
Tilen Švarc, Matej Zadravec, Žiga Jelen, Peter Majerič, Blaž Kamenik, Rebeka Rudolf, 2023, izvirni znanstveni članek

Opis: This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the ultrasonic spray pyrolysis technique. They were collected in a water suspension with polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with transmission electron microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was extruded, and the injection was moulded successfully. Flexural testing of PLA/Ni/Y2O3 showed a slight average decrease (8.55%) in flexural strength and a small decrease from 3.7 to 3.3% strain at the break, when compared to the base PLA. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in injection moulding applications and warrant further exploration of their properties and new applications in various fields.
Ključne besede: ultrasound spray pyrolysis, Ni/Y2O3, lyophilization, PLA, extrusion, injection moulding
Objavljeno v DKUM: 05.04.2024; Ogledov: 51; Prenosov: 1
.pdf Celotno besedilo (3,29 MB)
Gradivo ima več datotek! Več...

2.
Numerical analysis of fluid flow in a vial : [master thesis]
Žiga Časar, 2019, magistrsko delo

Opis: Lyophilization or freeze-drying is a widely used process in the pharmaceutical and food industry. In the process the solvent will be removed under extreme conditions of low temperature and low system pressures, whereby sublimation happens, the transition from the solid phase to the gas phase, with skipping the liquid phase, which happens bellow the triple point. This study focuses on numerical modeling at the start of the process, the so called primary drying. For this stage the highest mass flow rates of vapor are typical, since the driving force of the process is the pressure difference between the sublimation front and surrounding area. In this stage the non-bonded solvent is removed. Because of the extreme conditions the typical computational fluid dynamics approach is not suitable anymore and has to be corrected. One way to do this is to use additional models for fluid behavior at the solid wall. The study focuses on the influence of different boundary conditions on the solid wall, No-Slip, Free Slip and Maxwell Slip, and their effect on fluid flow inside the vial. A quantitative and qualitative comparison of the results is presented.
Ključne besede: Lyophilization, Knudsen number, computational fluid dynamics, fluid flow, numerical modeling, slip boundary condition
Objavljeno v DKUM: 09.07.2019; Ogledov: 1386; Prenosov: 190
.pdf Celotno besedilo (2,66 MB)

Iskanje izvedeno v 1.55 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici