| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Influence of biodiesel on injection, fuel spray, and engine characteristics
Breda Kegl, Stanislav Pehan, 2008, izvirni znanstveni članek

Opis: This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel under peak torque and ratedconditions. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of mineral diesel. The experimentally obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. Furthermore, the influence of biodiesel usage on lubrication is presented briefly. The results indicate that, by using biodiesel, harmful emissions (NOx, CO, HC, smoke, and PM) can be reduced to some extent by adjusting the injection pump timing properly while keeping other engine characteristics within acceptable limits. Furthermore, the results indicate better lubrication conditions when biodiesel is used.
Ključne besede: biodiesel, diesel engine, injection characteristics, fuel spray, emission, lubrication
Objavljeno: 31.05.2012; Ogledov: 1025; Prenosov: 169
.pdf Celotno besedilo (1,50 MB)
Gradivo ima več datotek! Več...

2.
Diesel and biodiesel fuel spray simulations
Primož Pogorevc, Breda Kegl, Leopold Škerget, 2008, izvirni znanstveni članek

Opis: This paper deals with the investigation of the influential parameters of a mathematical spray breakup model using different fuels. Beside injection system measurements, fuel physical properties and injection process characteristics were measured, because they are necessary for the spray simulation input. For validation purposes, spray was injected into motionless air at atmospheric pressure and room temperature and filmed with a high-speed camera. Spray macrocharacteristics have been determined on the recorded images. Using the simulation program, the injection processes for diesel, biodiesel, and their 50% blend B50 have been simulated. Spray mathematical model parameters were tuned based on the experimentally gained results. Primary breakup model parameters showed the biggest impact on the spray characteristics and were therefore expressed using the fuel physical properties, the injection process characteristics, and the working regime parameters. Spray simulations into the combustion chamber were made in the end. All of these results are presented and discussed in this paper.
Ključne besede: fuel spray, spray breakup, biodiesel fuel, fuels, numerical simulations, mathematical model
Objavljeno: 31.05.2012; Ogledov: 931; Prenosov: 50
URL Povezava na celotno besedilo

3.
Experimental investigation review of biodiesel usage in bus diesel engine
Breda Kegl, Marko Kegl, 2017, izvirni znanstveni članek

Opis: This paper assembles and analyses extensive experimental research work conducted for several years in relation to biodiesel usage in a MAN bus Diesel engine with M injection system. At first the most important properties of the actually used neat rapeseed biodiesel fuel and its blends with mineral diesel are discussed and compared to that of mineral diesel. Then the injection, fuel spray, and engine characteristics for various considered fuel blends are compared at various ambient conditions, with special emphasis on the influence of low temperature on fueling. Furthermore, for each tested fuel the optimal injection pump timing is determined. The obtained optimal injection pump timings for individual fuels are then used to determine and discuss the most important injection and combustion characteristics, engine performance, as well as the emission, economy, and tribology characteristics of the engine at all modes of emission test cycles test. The results show that for each tested fuel it is possible to find the optimized injection pump timing, which enables acceptable engine characteristics at all modes of the emission test cycles test.
Ključne besede: bus diesel engine, fuel injection, fuel spray, combustion, emission, engine performance, tribology characteristics, optimized injection pump timing
Objavljeno: 07.07.2017; Ogledov: 357; Prenosov: 200
.pdf Celotno besedilo (3,81 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.04 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici