| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 10 / 11
Na začetekNa prejšnjo stran12Na naslednjo stranNa konec
1.
Detecting and analysing condition of hydraulic oils with on-line sensors
Vito Tič, Darko Lovrec, 2011, izvirni znanstveni članek

Opis: On-line condition monitoring of the entire system or individual components can be used for detection of impending system break-down. The on-line monitoring of the state of hydraulic system and fluid plays a decisive role in general on-line condition monitoring. Friction, wear, leakage and excessive temperatures all have impact on lubricating properties of the oil. Apart from this, the oil its self is prone to aging and deterioration processes, which can also result in corrosion and equipment failures. The oil condition can be understood as a fingerprint of the condition of the complete system. Due to a widespread availability of robust and cost-effective on-line sensors for measuring various fluid properties, latest developments deal with on-line oil condition monitoring to determine the condition of hydraulic system and fluid. This allows for maintenance work to be carried out based on the detected system condition.
Ključne besede: oil ageing, condition monitoring, physical properties, chemical properties
Objavljeno: 01.06.2012; Ogledov: 844; Prenosov: 15
URL Povezava na celotno besedilo

2.
Intelligent cutting tool condition monitoring in milling
Uroš Župerl, Franc Čuš, Jože Balič, 2011, izvirni znanstveni članek

Opis: Purpose: of this paper is to present a tool condition monitoring (TCM) system that can detect tool breakage in real time by using a combination of neural decision system, ANFIS tool wear estimator and machining error compensation module. Design/methodology/approach: The principal presumption was that the force signals contain the most useful information for determining the tool condition. Therefore, ANFIS method is used to extract the features of tool states from cutting force signals. The trained ANFIS model of tool wear is then merged with a neural network for identifying tool wear condition (fresh, worn). Findings: The overall machining error is predicted with very high accuracy by using the deflection module and a large percentage of it is eliminated through the proposed error compensation process. Research limitations/implications: This study also briefly presents a compensation method in milling in order to take into account tool deflection during cutting condition optimization or tool-path generation. The results indicate that surface errors due to tool deflections can be reduced by 65-78%. Practical implications: The fundamental limitation of research was to develop a single-sensor monitoring system, reliable as commercially available system, but much cheaper than multi-sensor approach. Originality/value: A neural network is used in TCM as a decision making system to discriminate different malfunction states from measured signals.
Ključne besede: tool condition monitoring, TCM, wear, tool deflection, ANFIS, neural network, end-milling
Objavljeno: 01.06.2012; Ogledov: 851; Prenosov: 19
URL Povezava na celotno besedilo

3.
Solving exterior problems of wave propagation based on an iterative variation of local DtN operators
Miroslav Premrov, Igor Špacapan, 2004, izvirni znanstveni članek

Opis: This paper discusses the problem of wave reflection from the fictitious boundary, with particular regard to the higher harmonic modes. This problem occurs when solving the wave equation in exterior domains using an asymptotic local low-order Dirichlet-to-Neumann (DtN) map for computational procedures applied to a finite domain. We demonstrate that the amplitudes of the reflected fictitious harmonics depend on the wave number, the location of the fictitious boundary, as well as on the local DtN operator used in the computations. Moreover, we show that a constant value of the asymptotic local low-order operator cannot sufficiently eliminate the amplitudes of all reflected waves, and that the results are poor especially for higher harmonics. We propose therefore an iterative method, which varies the tangential dependence of the local operator in each computational step. We only discuss some logical and interesting choices for the operators although this method permits several possibilities on how to vary the operator. The method is simple to apply and the presented examples demonstrate that the accuracy is considerably improved by iterations.
Ključne besede: wave motion, infinite domains, fictitious boundary, radiation condition, finite element method, Dirichlet-to-Neumann map
Objavljeno: 01.06.2012; Ogledov: 947; Prenosov: 43
URL Povezava na celotno besedilo

4.
Bluetooth platform for wireless measurements using industrial sensors
Tadej Tašner, Kristian Les, Darko Lovrec, 2013, izvirni znanstveni članek

Opis: The past decade has seen significant advancement in the field of mobile devices. Various smart devices such as cellular phones, tablets and PDAs have become universal tools in our everyday lives. Their versatility is based on their computing power, portability and their integration with other devices and services such as the World Wide Web. However, these smart devices have an even wider usability spectrum. They can also be used for wireless industrial measurements using existing sensors. The wireless connectivity of existing industrial sensors is achieved by equipping them with a Bluetooth module, which digitizes the data and passes it to any Bluetooth capable smart device for further processing, evaluation and logging. This paper describes the specially designed Bluetooth platform for wireless measurements all the way from the basic concept, through hardware, firmware and software implementation, to the sample tests and measurements.
Ključne besede: sensors, wireless, bluetooth, data acquisition, condition monitoring
Objavljeno: 10.07.2015; Ogledov: 322; Prenosov: 135
.pdf Celotno besedilo (1,02 MB)
Gradivo ima več datotek! Več...

5.
6.
7.
Fault detection of an industrial heat-exchanger
Dejan Dragan, 2011, izvirni znanstveni članek

Opis: One of the key issues in modelling for fault detection is how to accommodate the level of detail of the model description in order to suit the diagnostic requirements. The paper addresses a two-stage modelling concept to an industrial heat exchanger, which is located in a tyre factory. Modelling relies on combination of prior knowledge and recorded data. During the identification procedure, the estimates of continuous model parameters are calculated by the least squares method and the state variable filters (SVF). It is shown that the estimates are largely invariant of the bandwidth of the SVFs. This greatly reduces the overall modelling effort and makes the whole concept applicable even to less experienced users. The main issues of the modelling procedure are stressed. Based on the process model a simple detection system is derived. An excerpt of the results obtained on operating records is given.
Ključne besede: industrijski prenosniki toplote, zaznavanje napak, nadzor procesov, odkrivanje napak na osnovi modela, modeliranje, identifikacija, industrial heat exchanger, fault detection, condition monitoring, model-based detection, modelling, identification
Objavljeno: 10.07.2015; Ogledov: 685; Prenosov: 7
URL Povezava na celotno besedilo

8.
Real-time cutting tool condition monitoring in milling
Franc Čuš, Uroš Župerl, 2011, izvirni znanstveni članek

Opis: Reliable tool wear monitoring system is one of the important aspects for achieving a self-adjusting manufacturing system. The original contribution of the research is the developed monitoring system that can detect tool breakage in real time by using a combination of neural decision system and ANFIS tool wear estimator. The principal presumption was that force signals contain the most useful information for determining the tool condition. Therefore, the ANFIS method is used to extract the features of tool states from cutting force signals. ANFIS method seeks to provide a linguistic model for the estimation of tool wear from the knowledge embedded in the artificial neural network. The ANFIS method uses the relationship between flank wear and the resultant cutting force to estimate tool wear. A series of experiments were conducted to determine the relationship between flank wear and cutting force as well as cutting parameters. Speed, feed, depth of cutting, time and cuttingforces were used as input parameters and flank wear width and tool state were output parameters. The forces were measured using a piezoelectric dynamometer and data acquisition system. Simultaneously flank wear at the cutting edge was monitored by using a tool maker's microscope. The experimental force and wear data were utilized to train the developed simulation environment based on ANFIS modelling. The artificial neural network, was also used to discriminate different malfunction states from measured signals. By developed tool monitoring system (TCM) the machining process can be on-line monitored and stopped for tool change based on a pre-set tool-wear limit. The fundamental limitation of research was to develop a single sensor monitoring system, reliable as commercially available system, but 80% cheaper than multisensor approach.
Ključne besede: end-milling, tool condition monitoring, wear estimation, ANFIS
Objavljeno: 10.07.2015; Ogledov: 814; Prenosov: 63
URL Povezava na celotno besedilo

9.
On-line condition monitoring and evaluation of remaining useful lifetimes for mineral hydraulic and turbine oils
Vito Tič, Darko Lovrec, 2017, znanstvena monografija

Opis: Condition monitoring of hydraulic and turbine oils, and especially their remaining useful life, is becoming an important strategic business advantage for plant owners, which benefits in environment protection and cost reduction. This monograph discusses the problem of condition monitoring of hydraulic fluids throughout their life-cycles. Particular emphasis is placed on assessing mineral-based oils’ conditions and their remaining useful lifetimes quantitatively. Practicality and usefulness are vital when developing and deploying various methods for condition monitoring systems within industrial environments. Therefore, it is important to know the oil degradation mechanisms and influencing factors, commonly used laboratory methods and oil ageing tests, as well as, for on-line condition monitoring system design, the available sensors with all their characteristics and restrictions. The proposed approach is based on a novel method for testing the durability and oxidation stability of different hydraulic and turbine oils. The developed mathematical model is based on data from previously conducted oil-ageing tests for the assessment of an oil's condition and its remaining useful lifetime. The method can also be used for comparison of different oils and selection of a more adequate oil with high oxidation stability and long service-lifetime.
Ključne besede: Hydraulic and turbine oils, degradation mechanisms, on-line condition monitoring, test methods, remaining useful lifetime
Objavljeno: 22.12.2017; Ogledov: 656; Prenosov: 128
.pdf Celotno besedilo (7,75 MB)
Gradivo ima več datotek! Več...

10.
A new solution for shallow and deep tunnels by considering the gravitational loads
Mohammad Reza Zareifard, Ahmad Fahimifar, 2012, izvirni znanstveni članek

Opis: A new, elasto-plastic, analytical-numerical solution, considering the axial-symmetry condition, for a circular tunnel excavated in a strain-softening and Hoek–Brown rock mass is proposed. To examine the effect of initial stress variations, and also the boundary conditions at the ground surface, the formulations are derived for different directions around the tunnel. Furthermore, the effect of the weight of the plastic zone is taken into account in this regard. As the derived differential equations have no explicit analytical solutions for the plastic zone, the finite-difference method (FDM) is used in this study. On the other hand, analytical expressions are derived for the elastic zone. Several illustrative examples are given to demonstrate the performance of the proposed solution, and to examine the effect of various boundary conditions. It is concluded that the classic solutions, based on the hydrostatic far-field stress, and neglecting the effect of the boundary conditions at the ground surface, give applicable results for a wide range of practical problems. However, ignoring the weight of the plastic zone in the analyses can lead to large errors in the calculations.
Ključne besede: ground-response curve, elasto-plastic analysis, boundary condition, axial symmetry, gravitational loads
Objavljeno: 13.06.2018; Ogledov: 268; Prenosov: 31
.pdf Celotno besedilo (406,96 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.26 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici