SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 7 / 7
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Properties of UV-cured pigment prints on textile fabric
Branko Neral, Sonja Šostar-Turk, Bojana Vončina, 2006, izvirni znanstveni članek

Opis: This paper studies and evaluates the UV-curing of pigment prints on textile fabric using a prototype UV scanner. A printing paste comprising synthetic thickener, emulgator, binder, pigment dispersion and photoinitiator was applied using a flat screen printing technique onto the cotton fabric, then dried and exposed to heat or UV-radiation under a mercury vapour lamp (200 W cm-2). The characteristics of cured prints such as paste add-on, colour properties, colour fastness to washing and dryžwet rubbing were evaluated, together with fabric stiffness. The effects of UV-curing were evaluated by Attenuated Total Reflectance Fourier transform infrared spectroscopy (ATR-FTIR). The properties of the UV-cured pigment prints were compared with those of the thermal cured prints. Analyses of the obtained results helped to define the optimum composition of the photo reactive pigment paste, and the UV-curing conditions under which satisfactory results were obtained, comparable with those from the thermal curing method.
Ključne besede: textiles, textile printing, printing quality, pigment dispersion, UV-curing, binder, photoinitiator
Objavljeno: 30.05.2012; Ogledov: 1283; Prenosov: 41
URL Povezava na celotno besedilo

2.
The use of artificial neural networks for colour prediction in textile printing
Darko Golob, Jure Zupan, Đurđica Parac-Osterman, 2008, objavljeni znanstveni prispevek na konferenci

Opis: An attempt of using artificial neural networks for the prediction of dzes in textile printing paste preparation is presented. An existing collection of printed samples served as the basis for neural network training. It consists of 1340 samples printed using either a single dze or a combination of two dzes. First the proper combination of dzes was determined, because in most cases onlz two dzes are combined in the printing paste. Then the necessarz concentration of each dze was predicted. The reflectance value, and the colourvalues L*, a*, b* serve as input data and the known combination and concentrations of dzes for each sample were the targets. Some variations of neural network were tested, as well as various numbers of neurons in the hidden lazer. In addition, the influence of the training set organisation was examined, together with the number of learning epochs on the learning success.
Ključne besede: artificial neural networks, textile printing, colour recipe prediction
Objavljeno: 31.05.2012; Ogledov: 995; Prenosov: 28
URL Povezava na celotno besedilo

3.
Wastewater treatment after reactive printing
Sonja Šostar-Turk, Marjana Simonič, Irena Petrinić, 2005, izvirni znanstveni članek

Opis: Membrane filtration of wastewater after textile printing with reactive dyes isdescribed. The wastewater from a Slovenian factory, whose output is approx. 80% reactive dyes printed and dyed on cotton, was studied. In particular, the presence of urea, sodium alginate, oxidation agent and reactive dyes, used forthe printing paste preparation, in the wastewater was studied. Chemical analyses of actual, non-purified, wastewater showed that many Slovenian regulations were exceeded. The study of membrane filtration is based on a pilot wastewater treatment plantČ ultrafiltration (UF) and reverse osmosis (RO) units. The quality of the wastewater was improved by ultrafiltration, butits effluent still does not conform to the specification of concentration limits for emission into water. Permeate coming from RO meets the required specification and, therefore, could be re-used in the washing process of printed textiles.
Ključne besede: textile printing, reactive dyes, wastewater treatment, membrane filtration, pilot plant
Objavljeno: 01.06.2012; Ogledov: 1517; Prenosov: 25
URL Povezava na celotno besedilo

4.
Rheological study of interactions between non-ionic surfactants and polysaccharide thickeners used in textile printing
Rebeka Fijan, Sonja Šostar-Turk, Romano Lapasin, 2007, izvirni znanstveni članek

Opis: The influence of four non-ionic surfactants (isododecyl and cetyl polyoxyethylene ethers) on aqueous polysaccharide solutions (sodium alginate, guar gum, and sodium carboxymethyl guar), applicable for textile printing pastes, were studied via rheological measurements. Rheology of polysaccharide-surfactant solutions in aqueous matrices is primarily governed by polymer content, which imparts marked shear-thinning and viscoelastic character to the system. Such properties are modulated in moderate but sensible way by changes in surfactant concentration or type. Above 3% surfactants addition to non-substituted guar gum solutions results in a significant impact leading to phase separation and a particular strongly associated phase is formed due to hydrogen bonds between ethylene oxy units from the surfactant and primary hydroxyl groups in guar. A satisfactory fitting of viscosity data is obtained with both the Cross equation and the Roberts-Barnes-Carew model. The experimental results of mechanical spectra can be described quite satisfactory with both the Friedrich-Braun and the generalized Maxwell models.
Ključne besede: textile printing, polysaccharide thickeners, rheology, non-ionic surfactant, polymer-surfactant interactions, viscoelasticity
Objavljeno: 01.06.2012; Ogledov: 937; Prenosov: 31
URL Povezava na celotno besedilo

5.
Good quality printing with reactive dyes using guar gum and biodegradable additives
Reinhold Schneider, Sonja Šostar-Turk, 2003, izvirni znanstveni članek

Opis: In printing with reactive dyes sodium alginates or synthetic thickeners are typically used as thickening agents to prevent unacceptable fabric handle. A new reactive printing process for reactive dyes on cellulosic textiles has been developed using natural thickening agents and environmental-friendly additives. Printing trials with guar gums have shown that the use of differentadditives can prevent fabric stiffness. These additives have no significant influence on rheology and colour strength but contributed to soft fabric handle even when guar gums were used as thickening agent. The use of additives and guar gum provide good quality prints with reduced wastewater pollution.
Ključne besede: textile printing, guar gum, additives, fabric handle, printing quality, ecology, environmental protection
Objavljeno: 01.06.2012; Ogledov: 1429; Prenosov: 26
URL Povezava na celotno besedilo

6.
Rheological studies of concentrated guar gum
Marija Oblonšek, Sonja Šostar-Turk, Romano Lapasin, 2003, izvirni znanstveni članek

Opis: Polymers and surfactants are essential ingredients of the printing paste. Polysaccharides are used commercially to thicken, suspend or stabilise aqueoussystems. Also they are used to produce gels and to act as flocculates, binders, lubricants, to serve as modifiers of film properties, and have a function as adjusters of rheological parameters. Surfactants, on the other hand, perform numerous functions acting as dispersants, wetting agents, emulsifiers and antifoaming agents. The rheological properties of polysaccharide thickeners (guar gums with different substitution levels and different producers) at different concentrations and temperatures and, second,the effects produced by the addition of nonionic surfactants (polyoxyethylene stearyl alcohols with different numbers of EO groups) have been studied under linear and nonlinear shear conditions. Experimental data have been correlated with the different modelsČ flow curves with the Cross, Carreau and Meter-Bird model, and mechanical spectra with the generalized Maxwell model and Friedrich-Braun model. The surface tensions of aqueous systems containing polysaccharide andžor surfactants have been determined overextended concentration ranges in order to detect the CMC conditions and toprovide a better understanding about the polysaccharide-surfactant interactions.
Ključne besede: textile printing, printing pastes, polysaccharides, thickeners, rheology, viscoelasticity, surfactants, guar gum
Objavljeno: 01.06.2012; Ogledov: 1264; Prenosov: 24
URL Povezava na celotno besedilo

7.
Dependence of warm or cold feeling and heat retention ability of knitwear from digital print parameters
Mladen Stančić, Dragana Grujić, Dragoljub Novaković, Nemanja Kašiković, Branka Ružičić, Jelka Geršak, 2014, izvirni znanstveni članek

Opis: Textile materials are increasingly being subjected to the process of printing. The printing process with its parameters significantly affects the properties of textile materials and clothes made from these materials. This paper examines the effect of the parameters of digital printing on thermo-physiological characteristics of printed textile materials. As the essential print parameters were selected tone value and a different number of passes. In this research were used knitted fabric materials of 100% cotton fibers (100% CO), 100% polyester fibers (100% PES) and their mixture (50%CO/50% PES). The influence of print parameters to thermo-physiological properties of the material is evaluated through a warm or cold feeling and heat retention ability. Results of the research demonstrated that, in addition to material composition, the printing process with its parameters have a significant influence on the thermo-physiological characteristics of textile materials.
Ključne besede: digital printing, textile materials, thermo-physiological comfort, warm of cold feeling, heat retention ability
Objavljeno: 09.08.2017; Ogledov: 217; Prenosov: 34
.pdf Celotno besedilo (934,30 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.2 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici