| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 2 / 2
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Assessment of the load-bearing capacity of a primary pipeline
Nenad Gubeljak, Jelena Vojvodič-Tuma, Borivoj Šuštaršič, Jožef Predan, Maks Oblak, 2007, izvirni znanstveni članek

Opis: High-alloyed Cr-Ni-based two-phase stainless steel (SS) cast alloys are commonly used in nuclear power plants. The mechanical equipment in these facilities can contribute to a reduction in its resistance to stable crack growth as a result of extended operating times and high temperatures. The toughness of these materials strongly depends on their delta (▫$/delta$▫) ferrite content, which spinodally decomposes into two phases with different ratios of Cr and Ni at a relatively low (slightly above 300 °C) temperature. This temperature is similar to the operating temperature of the vital parts, for example, the coolant system. The formation of two phases with the same crystalstructure but different lattice parameters causes internal elastic stresses that result in a hardness increase and an impact-toughness decrease. The result is an increased risk of crack formation in the stress-concentration zones such as the critical regions of different welded joints (e.g. "L, T, K and X" shapes). The values of the critical stress intensity factor change according to its position along the crack contour. Therefore, the aim of our study was to assess the influence of the materials' changes on the crack extension and the decrease of the primary pipeline's bearing capacity by taking account of the increased temperature and time of operation for the given loading conditions. The SINTAP (European Structural Integrity Assessment Procedure) was used for this assessment.
Ključne besede: welding, welded joints, pipelines, fracture toughness testing, structure integrity assessment procedure
Objavljeno: 01.06.2012; Ogledov: 983; Prenosov: 45
URL Povezava na celotno besedilo

2.
An integrity analysis of washing machine holders
Nenad Gubeljak, Matej Mejač, Jožef Predan, 2007, izvirni znanstveni članek

Opis: The paper deals with structure integrity analysis of the holder for the carrying cross of a washing machine drum. Premature fracture of the holder occurred between mechanical sustainable tests of washing machine in the factory. In order to prevent fracture, the task was to determine the reasons for premature fracture of the holder and to estimate the suitability of the new design of the holder cross. Input data for structure integriry analysis were obtained by material by mechanical testing of used materials. Stress and strain analysis of holder limit load was performed by finite element modeling of holder. Dynamic tests of holders with two different thicknesses were done on a servo-hydraulic machine in order to find dynamical strength and endurance of holder. Fracture behaviour of holders is defined as initiation and propagation of crack. The obtained behaviour confirmed that the new design of holders reduces stress concentration in the critical region. Consequently, the new holder subjected to the same dynamic load can endure a higher number of cycles until breakage. The total number of cycles overcomes industrial testing requirements.
Ključne besede: lomna mehanika, visokociklično utrujanje, preizkušanje lomne žilavosti, nosilci kadi pralnega stroja, mejna obremenitev, ocena celovitosti konstrukcije, fracture mechanics, high cycle fatigue, fracture toughness testing, washing machine holders, washing machine drums, structure integrity assessment, limit load
Objavljeno: 10.07.2015; Ogledov: 547; Prenosov: 45
.pdf Celotno besedilo (517,04 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.08 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici