Iskanje po katalogu digitalne knjižnice

Opis: In order to ensure efficient wastewater treatment and seawater desalination, adequate modeling and optimization of the forward osmosis (FO) process has the potential to be very helpful. This paper deals with the FO model parameters calibration and FO process optimization by a gradient-based optimization method. For this purpose, an upgraded FO model, which involves temperature- and agent-dependent parameters, was developed. The FO model calibration was done using NaCl as agents in draw solution, while MgCl2 was used for model validation. The agreements between simulated and measured FO performance were satisfactory; relative index of agreement are higher than 0.99. By using the proposed FO model, the optimization of FO process conditions was performed with various definitions of the objective and constraint functions. In case of maximizing the water flux, minimizing reverse solute flux, and fulfilling the required constraints, the ratio of water flux and reverse solute flux increased up to 40 % for NaCl and up to 20 % for MgCl2; meanwhile the effective osmotic pressure difference was improved 2-times for NaCl and up to 3.8-times for MgCl2. The optimization process proved to be stable and efficient and can easily be adapted or upgraded for more complex dynamic FO modeling.
Ključne besede: forward osmosis, modeling, model and process parameters, calibration procedure, gadient-based optimization
Objavljeno v DKUM: 23.08.2024; Ogledov: 67; Prenosov: 8
Celotno besedilo (12,72 MB)

Opis: The thesis researches the application of neural networks in computer program calibration of traffic micro-simulation models. The calibration process is designed on the basis of the VISSIM micro-simulation model of local urban roundabouts. From the five analyzed methods of computer program calibration, Methods I, II and V were selected for a more detailed research. The three chosen calibration methods varied the number of outgoing traffic indicators predicted by neural networks and a number of neural networks in the computer program calibration procedure. Within the calibration program, the task of neural networks was to predict the output of VISSIM simulations for selected functional traffic parameters - traveling time between the measurement points and queue parameters (maximum queue and number of stopping at the roundabout entrance). The Databases for neural network training consisted of 1379 combinations of input parameters whereas the number of output indicators of VISSIM simulations was varied. The neural networks (176 of them) were trained and compared for the calibration process according to training and generalization criteria. The best neural network for each calibration method was chosen by using the two-phase validation of neural networks. The Method I is the calibration method based on calibration of a traffic indicator -traveling time and it enables validation related to the second observed indicator – queue parameters. Methods II and V connect the previously described calibration and validation procedures in one calibration process which calibrates input parameters according to two traffic indicators. Validation of the analyzed calibration methods was performed on three new sets of measured data - two sets at the same roundabout and one set on another location. The best results in validation of computer program calibration were achieved by the Method I which is the recommended method for computer program calibration. The modeling results of selected traffic parameters obtained by calibrated VISSIM traffic model were compared with: values obtained by measurements in the field, the existing analysis methods of operational roundabouts characteristics (Lausanne method, Kimber-Hollis, HCM) and modeling by the uncalibrated VISSIM model. The calibrated model shows good correspondence with measured values in real traffic conditions. The efficiency of the calibration process was confirmed by comparing the measured and modeled values of delays, of an independent traffic indicator that was not used in the process of calibration and validation of traffic micro-simulation models. There is also an example of using the calibrated model in the impact analysis of pedestrian flows on conflicting input and output flows of vehicles in the roundabout. Different traffic scenarios were analyzed in the real and anticipated traffic conditions.
Ključne besede: traffic models, traffic micro-simulation, calibration of the VISSIM model, computer program calibration method, neural networks in the calibration process, micro-simulation of roundabouts, traffic modeling parameters, driving time, queue parameters, delay
Objavljeno v DKUM: 02.06.2011; Ogledov: 5471; Prenosov: 383
Celotno besedilo (13,21 MB)