1. Hierarchically porous polyacetylene networks : adsorptive photocatalysts for efficient bisphenol a removal from waterDavid Šorm, Jiří Brus, Albin Pintar, Jan Sedláček, Sebastijan Kovačič, 2024, izvirni znanstveni članek Ključne besede: polyacetylenes, emulsion-templating, π-conjugated networks, macroporous polymers, heterogeneous photocatalysis
Objavljeno v DKUM: 29.08.2024; Ogledov: 73; Prenosov: 3
 Povezava na datoteko |
2. Highly porous polymer beads coated with nanometer-thick metal oxide films for photocatalytic oxidation of bisphenol AGergő Ballai, Tomaž Kotnik, Matjaž Finšgar, Albin Pintar, Zoltán Kónya, András Sápi, Sebastijan Kovačič, 2023, izvirni znanstveni članek Opis: Highly porous metal oxide−polymer nanocomposites are attracting considerable interest due to their unique structural and functional features. A porous polymer matrix brings properties such as high porosity and permeability, while the metal oxide phase adds functionality. For the metal oxide phase to perform its function, it must be fully accessible, and this is possible only at the pore surface, but functioning surfaces require controlled engineering, which remains a challenge. Here, highly porous nanocomposite beads based on thin metal oxide nanocoatings and polymerized high internal phase emulsions (polyHIPEs) are demonstrated. By leveraging the unique properties of polyHIPEs, i.e., a three-dimensional (3D) interconnected network of macropores, and high-precision of the atomic-layer-deposition technique (ALD), we were able to homogeneously coat the entire surface of the pores in polyHIPE beads with TiO$_2$-, ZnO-, and Al$_2$O$_3$-based nanocoatings. Parameters such as nanocoating thickness, growth per cycle (GPC), and metal oxide (MO) composition were systematically controlled by varying the number of deposition cycles and dosing time under specific process conditions. The combination of polyHIPE structure and ALD technique proved advantageous, as MO-nanocoatings with thicknesses between 11 ± 3 and 40 ± 9 nm for TiO$_2$ or 31 ± 6 and 74 ± 28 nm for ZnO and Al$_2$O$_3$, respectively, were successfully fabricated. It has been shown that the number of ALD cycles affects both the thickness and crystallinity of the MO nanocoatings. Finally, the potential of ALD-derived TiO$_2$-polyHIPE beads in photocatalytic oxidation of an aqueous bisphenol A (BPA) solution was demonstrated. The beads exhibited about five times higher activity than nanocomposite beads prepared by the conventional (Pickering) method. Such ALD-derived polyHIPE nanocomposites could find wide application in nanotechnology, sensor development, or catalysis.
Ključne besede: nanovlakna, aerosoli, filtracija, emulsion-templating, macroporous polymers, atomic-layer-deposition
Objavljeno v DKUM: 15.04.2024; Ogledov: 249; Prenosov: 17
Povezava na celotno besedilo
Gradivo ima več datotek! Več... |
3. Aryl acrylate based high-internal-phase emulsions as precursors for reactive monolithic polymer supportsPeter Krajnc, Dejan Štefanec, Jane F. Brown, Neil R. Cameron, 2005, izvirni znanstveni članek Opis: Water-in-oil high-internal-phase emulsions (HIPEs), containing 4-nitrophenyl acrylate and 2,4,6-trichlorophenyl acrylate as reactive monomers, were prepared and polymerized, and highly porous monolithic materials resulted. The novel materials were studied by combustion analysis, Fourier transform infrared spectroscopy scanning electron microscopy, mercury porosimetry, and N2 adsorption/desorption analysis. With both esters, cellular macroporous monolithic polymers were obtained: the use of 4-nitrophenyl acrylate resulted in a cellular material with void diameters between 3 and 7 m and approximately3-m interconnects, whereas the use of 2,4,6-trichlorophenyl acrylate yielded a foam with void diameters between 2 and 5 m, most interconnects being around 1 m. The resulting monoliths proved to be very reactive toward nucleophiles, and possibilities of functionalizing the novel polymer supports were demonstrated via reactions with amines bearing additional functional groups and via the synthesis of an acid chloride derivative. Tris(hydroxymethyl)aminomethane and tris(2-aminoethyl)amine derivatives were obtained. The hydrolysis of 4-nitrophenylacrylate removed thenitrophenyl group, yielding a monolithic acrylic acid polymer. Furthermore,functionalization to immobilized acid chloride was performed very efficiently, with more than 95% of the acid groups reacting. The measurement of the nitrogen content in 4-nitrophenyl acrylate poly(HIPE)s after various times of hydrolysis showed the influence of the total pore volume of the monolithic polymers on the velocity of the reaction, which was faster with themore porous polymer.
Ključne besede: organic chemistry, macroporous polymers, monolithic polymer supports, emulsion polymerisation, foams, functionalization of polymers, high-internal-phase emulsions
Objavljeno v DKUM: 01.06.2012; Ogledov: 2329; Prenosov: 97
Povezava na celotno besedilo |
4. Acrylic acid "reversed" polyHIPEsPeter Krajnc, Dejan Štefanec, Irena Pulko, 2005, izvirni znanstveni članek Opis: An oil-in-water high internal phase emulsion consisting of acrylic acid, water, and a crosslinker (N,N-methylene bisacrylamide) as the water phase, and toluene as the oil phase was successfully stabilised to sustain thermal initiation of radical polymerisation resulting in porous open-cellular monolithic material. The type of initiator used influenced the average pore size ranging from approx. 708 nm to approx. 1 087 nm, as determined by mercury porosimetry.
Ključne besede: hydrophilic polymers, macroporous polymers, poly (acrylic acid), polyHIPE, supports
Objavljeno v DKUM: 01.06.2012; Ogledov: 2588; Prenosov: 102
Povezava na celotno besedilo |
