| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Influence of biodiesel on injection, fuel spray, and engine characteristics
Breda Kegl, Stanislav Pehan, 2008, izvirni znanstveni članek

Opis: This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel under peak torque and ratedconditions. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of mineral diesel. The experimentally obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. Furthermore, the influence of biodiesel usage on lubrication is presented briefly. The results indicate that, by using biodiesel, harmful emissions (NOx, CO, HC, smoke, and PM) can be reduced to some extent by adjusting the injection pump timing properly while keeping other engine characteristics within acceptable limits. Furthermore, the results indicate better lubrication conditions when biodiesel is used.
Ključne besede: biodiesel, diesel engine, injection characteristics, fuel spray, emission, lubrication
Objavljeno: 31.05.2012; Ogledov: 1002; Prenosov: 151
.pdf Celotno besedilo (1,50 MB)
Gradivo ima več datotek! Več...

2.
Dependence of material characteristics on lubrication in bulk forming process
Leo Gusel, 2009, objavljeni znanstveni prispevek na konferenci

Opis: In the paper the influence of coefficient of friction (lubricant) on different properties of cold formed material has been examined. Tensile tests, hardness measurements and electrical conductivity measurements were performed.In the frame of the experimental work the process of cold forward extrusion of a cylinder made from copper alloy was investigated. The specimens were extruded at four different lubricants coefficients of friction. The results have shown that use of different lubricators with different coefficients of friction can have effects on the material properties during and after cold forming process.
Ključne besede: lubrication, cold forming, copper alloy, mechanical properties
Objavljeno: 31.05.2012; Ogledov: 855; Prenosov: 9
URL Povezava na celotno besedilo

3.
Analysis of a strain rate field in cold formed material using the visioplasticity method
Leo Gusel, Rebeka Rudolf, Borut Kosec, 2009, kratki znanstveni prispevek

Opis: In this paper the visioplasticity method is used to find the complete velocity and strain rate distributions from the experimental data, using the finite-difference method. The data about values of strain rates in plastic re- gion of the material is very important for calculating stresses and the prediction of product quality. Specimens of copper alloy were extruded with different lubricants and different coefficients of friction and then the strain rate distributions were analysed and compared. Significant differences in velocity and strain rate distributions were obtained in some regions at the exit of the deformed zone.
Ključne besede: forward extrusion, copper alloy, visioplasticity, strain rate, lubrication
Objavljeno: 03.07.2017; Ogledov: 132; Prenosov: 41
.pdf Celotno besedilo (733,12 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.1 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici