| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Nanofoils for soldering and brazing in dental joining practice and jewellery manufacturing
Karlo Raić, Rebeka Rudolf, Borut Kosec, Ivan Anžel, Vojkan Lazić, Aleksandar Todorović, 2009, izvirni znanstveni članek

Opis: This paper describes the development of novel, reactive Al-Au nano-multilayered foils, their possible application in different fields and a discussion of the nano-foils' suitability for dental and jewellery applications. Moreover, this study includes the rapid joining of similar and dissimilar materials, by placing multilayer nano-foils and two layers of solder or braze. The foils precisely control the instantaneous release of heatenergy for the joining and act as a controllable local heat source. The reactive foils' thickness is in the range 10 nm to less than 100 nm and they contain many nanoscale layers that alternate between materials with high mixing heats, such as Al and Au. The foil between the two solder/braze layers melts the solder/braze with the heat generated by the reaction and bonds the components. The use of reactive foils eliminates the need for a furnace and dramatically increases the soldering/brazing heating rate of the components being bonded. Thus, ceramics and metals can be fused over required areas without the thermal stresses that are encountered in furnace soldering or brazing. In addition, a completely new plasma technology is proposed for the manufacturing of nano-foils and the first results of the preliminary experimental testing are presented.
Ključne besede: ceramic-metal bonding, low-temperature, nano-foils, plasma technology, dentistry, jewellery
Objavljeno: 01.06.2012; Ogledov: 1205; Prenosov: 34
.pdf Celotno besedilo (175,31 KB)
Gradivo ima več datotek! Več...

2.
Liquid metal/ceramic interfaces in dental practice and jewellery manufacturing
Karlo Raić, Rebeka Rudolf, Aleksandar Todorović, Dragoslav Stamenković, Ivan Anžel, 2010, pregledni znanstveni članek

Opis: Metal-ceramic fusing has been the essential step in obtaining materials that benefit from both ceramic and metal constituents, i.e. where the combined properties of metal and ceramic layers are desirable. When considering fusing methods, soldering and active metal brazing are the most effective. These processes involve braze melting and flowing between the two pieces of material. In the first part the phenomena occurring on the boundary between the ceramics and the active filler metal during the metal-ceramics joining are discussed. Three interconnected sub-processes are considered: (1) wetting of the ceramic surface, (2) chemical reactions at the interface and (3) diffusion with a moving interface. Then, the appearances at the grain boundary grooves of the ceramic surface are presented as phenomena on the catalytic surface. In the second part, examples from dental practice and jewellery manufacturing are used for comparative analysis. Finally, we discuss the composition and properties of the soldering and brazing alloys used for dental practice and jewellery manufacturing.
Ključne besede: metal-ceramic bonding, brazing, soldering, dentistry, jewellery
Objavljeno: 10.07.2015; Ogledov: 497; Prenosov: 39
.pdf Celotno besedilo (479,04 KB)
Gradivo ima več datotek! Več...

3.
Artificial tooth and polymer-base bond in removable dentures: the influence of pre-treatment on technological parameters to the bond`s strength
Martin Pavlin, Rebeka Rudolf, Vjekoslav Jerolimov, 2008, izvirni znanstveni članek

Opis: The aim of this study was to evaluate the artificial tooth and polymerbase bond, and to measure any formatted gaps between tooth and base. Acrylic models were classified into four groups depending on the type of surface pre-treatment. A pre-treatment surface combining mechanical and chemical led to the highest bond strength between acrylic tooth and denture-base. The fore-mentioned pre-treatment had an influenced on gap formation with an average value of 68.250 micro m, which is 70 % of the gap for the untreated samples. Furthermore, the measured compressive strength was above 6000 N/mm2, yet only 3200 N/mm2 on the untreated samples.
Ključne besede: artificial tooth, acrylic tooth, polymer base bond, dentistry
Objavljeno: 21.12.2015; Ogledov: 317; Prenosov: 14
URL Povezava na celotno besedilo

Iskanje izvedeno v 0.09 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici