| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 4 / 4
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Analysis of a strain rate field in cold formed material using the visioplasticity method
Leo Gusel, Rebeka Rudolf, Borut Kosec, 2009, kratki znanstveni prispevek

Opis: In this paper the visioplasticity method is used to find the complete velocity and strain rate distributions from the experimental data, using the finite-difference method. The data about values of strain rates in plastic re- gion of the material is very important for calculating stresses and the prediction of product quality. Specimens of copper alloy were extruded with different lubricants and different coefficients of friction and then the strain rate distributions were analysed and compared. Significant differences in velocity and strain rate distributions were obtained in some regions at the exit of the deformed zone.
Ključne besede: forward extrusion, copper alloy, visioplasticity, strain rate, lubrication
Objavljeno: 03.07.2017; Ogledov: 347; Prenosov: 73
.pdf Celotno besedilo (733,12 KB)
Gradivo ima več datotek! Več...

2.
3.
Dependence of material characteristics on lubrication in bulk forming process
Leo Gusel, 2009, objavljeni znanstveni prispevek na konferenci

Opis: In the paper the influence of coefficient of friction (lubricant) on different properties of cold formed material has been examined. Tensile tests, hardness measurements and electrical conductivity measurements were performed.In the frame of the experimental work the process of cold forward extrusion of a cylinder made from copper alloy was investigated. The specimens were extruded at four different lubricants coefficients of friction. The results have shown that use of different lubricators with different coefficients of friction can have effects on the material properties during and after cold forming process.
Ključne besede: lubrication, cold forming, copper alloy, mechanical properties
Objavljeno: 31.05.2012; Ogledov: 1198; Prenosov: 15
URL Povezava na celotno besedilo

4.
Modeling of impact toughness of cold formed material by genetic programming
Leo Gusel, Miran Brezočnik, 2006, izvirni znanstveni članek

Opis: In the paper, an approach completely different from the conventional methods for determination of accurate models for the change of properties of cold formed material, is presented. This approach is genetic programming (GP) method which is based on imitation of natural evolution of living organisms. The main characteristic of GP is its non-deterministic way of computing. No assumptions about the form and size of expressions were made in advance, but they were left to the self organization and intelligence of evolutionary process. First, copper alloy rods were cold drawn under different conditions and then impact toughness of cold drawn specimens was determined by Charpy tests. The values of independent variables (effective strain, coefficient of friction) influence the value of the dependent variable, impact toughness. On the basis of training data, different prediction models for impact toughness were developed by GP. Only the best models, gained by genetic programming were presented in the paper. Accuracy of the best models was proved with the testing data set. The comparison between deviation of genetic model results and regression model results concerning the experimental results has showed that genetic models are more precise and more varied then regression models.
Ključne besede: metal forming, genetic programming, evolutionary computing, impact toughness, copper alloy, modelling
Objavljeno: 30.05.2012; Ogledov: 1716; Prenosov: 89
URL Povezava na celotno besedilo

Iskanje izvedeno v 0.07 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici