| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 4 / 4
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Vloga in nastanek mikrostrukturnih sestavin M-A v zvarnih spojih maloogljičnih visokotrdnostnih konstrukcijskih jekel
Zdravko Praunseis, Masao Toyoda, Alojz Križman, Mitsuru Ohata, 2001, pregledni znanstveni članek

Opis: The existence of martensite-austenite constituents in the weld metal and heat-affected zone seriously reduces the fracture toughness of the welded joint. Therefore, we have investigated the formation of the martensite-austenite constituents when high-strength low-alloy steel is welded with a high heat input or using multi-pass welding. This paper deals with the effects of martensite-austenite constituents on the fracture toughness, the metallurgical features of the martensite-austenite constituents, and the prevention and elimination of the martensite-austenite constituents in the welded joints.
Ključne besede: arc welding, high-strength low-alloy steels, microstructure, martensite-austenite constituents, weld metal, heat-affected zone, cooling rate
Objavljeno: 01.06.2012; Ogledov: 1146; Prenosov: 60
.pdf Celotno besedilo (985,12 KB)
Gradivo ima več datotek! Več...

2.
The influence of cooling rate on the microstructure of an Al-Mn-Be alloy
Niko Rozman, Tonica Bončina, Ivan Anžel, Franc Zupanič, 2008, izvirni znanstveni članek

Opis: In ternary Al-Mn-Be alloys a metastable quasicrystalline phase can form at relatively low cooling rates (≈ 100 K/s); however, besides the quasicrystalline phase other phases can also be present. We found that the investigated alloy is very prone to the formation of metastable phases, which are also quasicrystalline. Using different investigation methods we determined the type of phases, their shape, morphology, chemical composition and distribution. Special attention was given to the micro- and nano-sized quasicrystalline particles. When using slow cooling, Al10Mn3 and Be4AlMn were present; however, with a faster cooling rate a quasicrystal approximant and a quasicrystalline phase were formed.
Ključne besede: aluminium, quasicrystals, cooling rate, microstructure
Objavljeno: 10.07.2015; Ogledov: 568; Prenosov: 30
.pdf Celotno besedilo (138,43 KB)
Gradivo ima več datotek! Več...

3.
Effect of cooling rate on the microstructure of an Al94Mn2Be2Cu2 alloy
Tonica Bončina, Boštjan Markoli, Franc Zupanič, 2012, izvirni znanstveni članek

Opis: In this study the effect of the cooling rate on the microstructure of Al94 Mn2 Be2 Cu2 alloy was investigated. The vacuum induction melted and cast alloy was exposed to different cooling rates. The slowest cooling rate was achieved by the DSC (10 K·min^−1), the moderate cooling rate succeeded by casting in the copper mould (≈1 000 K·s−1) and the rapid solidification was performed by melt spinning (up to 10^6 K·s^−1). The microstructure of the DSC-sample consisted of α-Al matrix, and several intermetallics: τ1-Al29 Mn6 Cu4 , Al4 Mn, θ-Al2 Cu and Be4 Al(Mn,Cu). The microstructures of the alloy at moderate and rapid cooling consisted of the α-Al matrix, i-phase and θ-Al2 Cu. Particles of i-phase and θ-Al2 Cu were much smaller and more uniformly distributed in melt-spun ribbons.
Ključne besede: Al-alloy, metallography, microstructure, cooling rate, solidification
Objavljeno: 03.07.2017; Ogledov: 234; Prenosov: 48
.pdf Celotno besedilo (231,30 KB)
Gradivo ima več datotek! Več...

4.
The microstructure and properties of materials at the fusion line
Vladimir Gliha, 2005, izvirni znanstveni članek

Opis: In this paper, the formation of the HAZ that is caused by the thermal effects of welding is investigated from the theoretical and experimental points of view. Samples of the material found at the fusion line were prepared by simulating the thermal regimes that occur during welding. A number of CCT diagrams that are valid for the conditions during welding were designed, and the hardness and impact-toughness of the samples were measured. This information was then related to the results of metallographic examinations. The maximum temperature and the cooling rate of the applied thermal cycles were found to be decisive in terms of the properties of HAZ.
Ključne besede: welding, HAZ, thermal cycle, cooling rate, fusion line
Objavljeno: 03.07.2017; Ogledov: 1212; Prenosov: 65
.pdf Celotno besedilo (270,09 KB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.1 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici