| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Analysis of composite T beam composed of timber, concrete and carbon strip
Matjaž Tajnik, Peter Dobrila, Miroslav Premrov, 2007, izvirni znanstveni članek

Opis: This paper provides a mathematical model and numerical example of composite T-section composed of a concrete plate and a timber beam strengthened at the bottom tension side with a carbon fibre-reinforced polymer (CFRP) strip. Analysis is provided in accordance with the European standards for timber, steel and concrete structures. The tensile strength of the carbon strip as well as the compressive strength of the concrete plate are higher than the bending strength of the timber beam, therefore it is convenient to use such composition of material to gain a higher load bearing capacity. It has been shown that the inclusion of CFRP strip reinforcement on the increase of load carrying and bending stiffness capacity was not as high as expected. On the other hand, we realized the importance of variety of material grade and geometrical properties combinations between sub-components which can significantly improve load bearing capacity and stiffness of composed beam. Furthermore, the CFRP strip contribution to the bending resistance and stiffness of the element is presented as a function of the fastener spacing intervals between concrete plate and timber beam.
Ključne besede: composite structures, timber structures, carbon strip, load bearing capacity, modeling
Objavljeno: 31.05.2012; Ogledov: 1137; Prenosov: 49
URL Povezava na celotno besedilo

2.
Cost estimation, optimization and competitiveness of different composite floor systems
Uroš Klanšek, Stojan Kravanja, 2006, izvirni znanstveni članek

Opis: This paper presents self-manufacturing cost estimation, cost optimization and competitiveness of different composite floor systems: composite I beams, composite trusses produced from rolled channel sections and composite trusses made from cold formed hollow sections. Part 1 of this two-part series of papers presents the estimation of the self-manufacturing (direct production) costs for composite and steel structures. The self-manufacturing costs are proposed to be defined as the sum of the material, the power consumption and the labour costs. The material costs of the structural steel, concrete, reinforcement, the shear connectors, electrodes, the anti-corrosion, fire protection and top coat painting, the formwork floor-slab panels and gas consumption are presented in detail. The power consumption costs comprise costs of sawing the steel sections, edge grinding, drilling, welding, stud welding and vibrating the concrete. The labour costs (times) presented define the costs of metal cutting, edge grinding, preparation, assembling and tacking, welding, welding of shear connectors, steel surface preparation and protection, drilling, cutting, placing and connecting the reinforcement, concreting, consolidating and curing the concrete. New approximation functions are proposed for the calculation of some manufacturing times and material consumptions. As the discussed costs vary significantly around the world, the proposed cost expressions are given in the open form to be used for cost estimation in different economic conditions. A numerical example of the estimation of the self-manufacturing costs for a composite I beam floor system shows the suitability of the proposed approach. On the basis of the defined self-manufacturing costs, introduced in Part 1, the cost optimization and the competitiveness of different composite floor systems are discussed in Part 2.
Ključne besede: cost estimation, self-manufacturing costs, material costs, power consumption costs, labour costs, steel structures, composite structures, welded structures
Objavljeno: 30.05.2012; Ogledov: 1307; Prenosov: 18
URL Povezava na celotno besedilo

3.
Experimental testing of single APM spheres
Matej Vesenjak, Lovre Krstulović-Opara, 2010, objavljeni znanstveni prispevek na konferenci

Opis: Advanced pore morphology (APM) foam, consisting of sphere-like metallic foam elements, proves to have advantageous mechanical properties and unique application adjustability. Since the APM foam manufacturing procedure has been developed recently, the mechanical characterization of these materials is still very limited. Therefore, the purpose of this research was to determine the behaviour of APM spheres and its composites when subjected to quasi-staticand dynamic compressive loading. The results of the performed research have shown valuable mechanical properties of the composite APM foam structures, offering new possibilities for their use in general engineering applications.
Ključne besede: advanced pore morphology, foam, composite APM foam structures
Objavljeno: 26.07.2017; Ogledov: 389; Prenosov: 150
.pdf Celotno besedilo (1,61 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.1 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici