Iskanje po katalogu digitalne knjižnice

Opis: Bender-element (BE) tests were conducted on clay-sand mixtures to investigate the variation of small strain-shear modulus (Gmax) with the sand content and the physical characteristics (size, shape) of the sand grains in the mixtures. Three different gradations (0.6–0.3 mm, 1.0–0.6 mm and 2.0–1.0 mm) of sands having distinct shapes (rounded, angular) were added to a low-plasticity clay with mixture ratios of 0% (clean clay), 10%, 20%, 30%, 40%, and 50%. For the purposes of performing a correlation analysis, unconfined compression (UC) tests were also carried out on the same specimens. The tests indicated that both the Gmax and unconfined compressive strength (q u) values of the specimens with angular sand grains were measured to be lower than those with rounded sand grains, for all sizes and percentages. As the percentage of sand in the mixture increases, the Gmax values increase, while the qu values decrease. The results further suggested that the Gmaxvalues decrease as the q u values decreases as the size of the sand grains reduces.
Ključne besede: sand, clay, bender element, unconfined compressive strength
Objavljeno v DKUM: 11.10.2018; Ogledov: 1554; Prenosov: 379
Celotno besedilo (844,22 KB)
Gradivo ima več datotek! Več...

Opis: The effects of coconut fibre on the mechanical characteristics of lime-treated clay are investigated in this study. The lime-treated clay specimens were prepared with a variety of coconut-fibre contents, i.e., 0.5%, 1%, 1.5% and 2%, in terms of the weight of dry soil. The stabilized specimens were tested at 7, 28 and 90 days after the treatment in order to observe the evolution of the mechanical resistance with time. The results of the unconfined compressive strength tests were used to determine the relationships between the compressive strengths and the indirect tensile strengths of the stabilized soil. Furthermore, the optimum percentage of coconut fibre mixed in the soil/lime mixtures was 1% of the dry mass and reinforcement at 90 days increases the peak compressive strength and the indirect tensile strength. Coconut-fibre inclusion changes the brittle behaviour of the lime-treated clay soil to give it a more ductile character.
Ključne besede: coconut fibre, lime, compressive strength, indirect tensile strength, clay soil, failure characteristics
Objavljeno v DKUM: 14.06.2018; Ogledov: 1286; Prenosov: 54
Celotno besedilo (755,61 KB)
Gradivo ima več datotek! Več...

Opis: This paper presents a comparison of field measurements and a numerical model of settlements based on the construction of an embankment on soft soil for the Cirebon Power Plant Project in Indonesia, where prefabricated vertical drains (PVDs) were installed. In the numerical model, floating PVDs in two soil layers for two- and one-way drainage conditions are examined in order to determine the optimum penetration depth. In this study, good agreement between the field measurements of the settlements and the numerical prediction could be achieved. An interesting result of this study is that the differences in the stiffness and/or the permeability in the unimproved area below the PVD tip have a significant influence on the optimum penetration depth (L/H) in the two-soil-layer condition. The numerical study showed that it is possible to use floating PVDs in single drainage conditions if the second layer is stiffer and/or more permeable than the first layer.
Ključne besede: two soil layers, floating prefabricated vertical drain, double and single drainage, numerical model, soft clay, consolidation
Objavljeno v DKUM: 13.06.2018; Ogledov: 1243; Prenosov: 90
Celotno besedilo (727,36 KB)
Gradivo ima več datotek! Več...

Opis: In this study, numerical predictions of the scale effect for circular footings supported by partially replaced, compacted, layers on natural clay deposits are presented. The scale- effect phenomenon was analyzed according to the footing sizes. Numerical analyses were carried out using an axisymmetric, two-dimensional, finite-element program. Before conducting the analysis, the validity of the constitutive model was validated using field tests performed by authors with seven different footing diameters up to 0.90 m and with three different partial replacement thicknesses. It is shown that the behavior of the circular footings on natural clay soil and the partial replacement system can be reasonably well represented by the Mohr Coulomb model. The Mohr-Coulomb model parameters were derived from the results of conventional laboratory and field tests. After achieving a good consistency between the results of the test and the numerical analysis, the numerical analyses were continued by increasing the footing diameter up to 25 m, considering the partial replacement thickness up to two times the footing diameter. The results of this parametric study showed that the stabilization had a considerable effect on the bearing capacity of the circular footings and for a given value of H/D the magnitude of the ultimate bearing capacity increases in a nonlinear manner with the footing diameter. The Bearing Capacity Ratio (BCR) was defined to evaluate the improved performance of the reinforced system. It was found, based on numerical and field-test results that the BCR of the partially replaced, natural clay deposits increased with an increase in the footing diameter and there was no significant scale effect of the circular footing resting on natural clay deposits.
Ključne besede: scale effect, circular footing, field test, finite-element analysis, natural clay, granular fill
Objavljeno v DKUM: 13.06.2018; Ogledov: 1226; Prenosov: 154
Celotno besedilo (554,10 KB)
Gradivo ima več datotek! Več...

Opis: A dredging process is essential for the development of harbours and ports, allowing the functional daily operation of the port. The management of dredged material represents a worldwide challenge, especially considering unwanted deposition of material. Because of their chemical, petrographic, mineralogical and homogeneity composition, marine sediments could represent an appropriate raw material for the brick industry, particularly for the production of clay blocks, roofing and ceramic tiles. In this study dredged material from Port of Koper was tested for such use, thus various analyses were carried out in order to determine if the dredged material is environmentally friendly and suitable for use in the brick industry. These included: chemical analysis, mineralogical analysis, particle size analysis, chloride content analysis and tests of firing in a gradient furnace. Furthermore, tests of mechanical properties, as well as tests of the frost-resistance of the samples were carried out. On the basis of the primary analyses and samples prepared in a laboratory, it was confirmed that marine sediments from the Port of Koper, without any additives are only conditionally suitable as a source material for producing brick products, because without additives they exhibit too much shrinkage on drying and firing, as well as high water absorption, this can be improved by the incorporation of suitable additives, for example, virgin clay or other suitable waste material. The approach described herewith can also be followed to assess sediments from other ports and rivers regarding its potential use in clay brick sector.
Ključne besede: dredge marine sediment, recycling, clay bricks, mechanical properties, chemical analysis
Objavljeno v DKUM: 21.12.2017; Ogledov: 2620; Prenosov: 196
Celotno besedilo (447,79 KB)
Gradivo ima več datotek! Več...