| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 2 / 2
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Assembly line optimization using MTM time standard and simulation modeling—A case study
Matic Breznik, Borut Buchmeister, Nataša Vujica-Herzog, 2023, izvirni znanstveni članek

Opis: This study presents an approach to solving the assembly line balancing problem (ALBP) using the Methods-Time Measurement (MTM) time standard and simulation software. ALBP is a common problem in manufacturing where a set of tasks with fixed times must be assigned to a series of sequential workstations in order to minimize the total idle time and reduce the assembly cost per product. This study uses MTM, a widely used production process scheduling method, to create a new time analysis of an assembly process that was previously balanced using the Work-Factor method and time study. This literature review shows that there are a lack of combinations of updated time analyses with newer simulation approaches in the current literature, and this was the motivation for the present work. An assembly line simulation was performed using Simio software to evaluate different design options and operating scenarios. The results show that the use of MTM and simulation can help minimize idle time and improve assembly line performance, thereby reducing costs and increasing efficiency. This study shows that the approach of using MTM and simulation is effective in solving ALBP and is a useful tool for manufacturing companies to improve the performance of their assembly lines and reduce costs.
Ključne besede: optimization, production planning, assembly line, MTM time standard, simulation, industry 4.0
Objavljeno v DKUM: 23.05.2023; Ogledov: 313; Prenosov: 38
.pdf Celotno besedilo (3,25 MB)

2.
Workloads and standard time norms in garment engineering
Zvonko Dragičević, Daniela Zavec Pavlinič, Jelka Geršak, 2002, izvirni znanstveni članek

Opis: Posibilities of new methods for measuring loading and standard time norms are presented, as applied in the field of garment engineering. Measurements deescribed are performed on modern measuring equipment designed to measure and perform computer analysis of temporal values of processing parameters in sewing operation and simultaneously record in two planes using a video system. The measuring system described was used to investigate sewing operation for the seam on a ladies' fashion suit, 52 cm long. For the operation investigated, method of work employing the MTM (Methods Time Measurements) system with analysis of basic movements was selected. The MTM system used shows that normal time for the operation in question is around 429.3 TMU (15.5 s). Investigations of workload imposed on the worker according to the OADM method were done simultaneously, and total ergonomic loading coefficients of Ker=0.082 was established, thus determining the time necessary to organise the process of work as 464.5 TMU (16.7 s). Simultaneous measurements of time and dynamic changes of processing parameters, as well as logical sets of movements, are important for defining favourable operation structures, time norms ergonomically designed systems of work and workplaces in garment engineering, as early as in the phase of designing operation. The investigations described make possible to find optimal distribution of working elements and zones of reach important for ergonomic designing and/or re-designing of workplaces, which results in considerably reduced level of fatigue in work optimal quality level, higher degree of utilisation of equipment installed and lower manufacturing costs.
Ključne besede: garment engineering, sewing, standard time norms, norms, time study, work study, MTM, motion timestudy measurement
Objavljeno v DKUM: 01.06.2012; Ogledov: 1860; Prenosov: 56
URL Povezava na celotno besedilo

Iskanje izvedeno v 0.06 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici