| | SLO | ENG | Piškotki in zasebnost

Večja pisava | Manjša pisava

Iskanje po katalogu digitalne knjižnice Pomoč

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 10 / 40
Na začetekNa prejšnjo stran1234Na naslednjo stranNa konec
1.
2.
Kalibracija merilnih kladic : SOP 4
Andrej Godina, Bojan Ačko, 2006, elaborat, predštudija, študija

Ključne besede: tehnološke meritve, kalibracija naprav, merilne kladice, akreditacija postopkov
Objavljeno: 31.05.2012; Ogledov: 1211; Prenosov: 49
URL Povezava na celotno besedilo

3.
4.
5.
Kalibracija tračnih meril : SOP 23
Andrej Godina, Bojan Ačko, 2006, elaborat, predštudija, študija

Ključne besede: tehnološke meritve, kalibracija naprav, tračna merila, akreditacija postopkov
Objavljeno: 31.05.2012; Ogledov: 1091; Prenosov: 35
URL Povezava na celotno besedilo

6.
Kontrola dolžinskih meril po MID : SOP 27
Andrej Godina, Bojan Ačko, 2006, elaborat, predštudija, študija

Ključne besede: tehnološke meritve, kalibracija naprav, dolžinska merila, akreditacija postopkov
Objavljeno: 31.05.2012; Ogledov: 1238; Prenosov: 20
URL Povezava na celotno besedilo

7.
8.
New approach to uncertainty evaluation in the calibration of gauge block comparators
Andrej Godina, Bojan Ačko, Marjan Družovec, 2007, izvirni znanstveni članek

Opis: Gauge blocks (GBs) are being calibrated by two methods: interferometric calibration and calibration by mechanical comparison to reference GB. While interferometric method represents primary level, comparison is more suitable for calibrating industrial GBs because of lower costs and shorter calibration time. Although no significant changes in equipment happened in last decade, improvements in mechanical comparison are on-going. In addition to the uncertainty of the reference GB calibration, uncertainty of the GB comparator is the most important contribution to total uncertainty of the mechanical calibration. The article introduces a new approach for evaluating the uncertainty of GB comparator calibration. The uncertainty budget and results of analytical and experimental evaluation of all contributions are presented. This approach results in lower end-effect uncertainty and a slightly higher length dependent uncertainty, in comparison with the uncertainty evaluation procedure as described in EA document EA-10/02.
Ključne besede: measurements, calibration, measuring uncertainty, gauge block, comparator, CMC, mechanical comparison
Objavljeno: 31.05.2012; Ogledov: 1527; Prenosov: 75
URL Povezava na celotno besedilo

9.
Simulation of line scale contamination in calibration uncertainty model
Marjan Družovec, Bojan Ačko, Andrej Godina, Tatjana Welzer-Družovec, 2008, izvirni znanstveni članek

Opis: Precise calibration of quartz line scales is very important for assuring traceability of microscopic measurements. Very significant influence in calibration uncertainty budget is represented by uncertainty of line centre detection. Line centre is usually detected through video signal processing using different types of algorithms. This paper is presenting calibration procedure that was developed in the Laboratory for Production Measurement at the Faculty of Mechanical Engineering in Maribor. It is focused in uncertainty analysis and especially in the influence of line scale contamination on determination of line centre position. Different types of line scale contamination like dirt spots, scratches, line edge incorrectness, and line intensity were simulated in order to test the ability of the line centre detection algorithm to eliminate such influences from the measurement results.
Ključne besede: line scale, calibration, uncertainty, video-positioning system, simulation
Objavljeno: 31.05.2012; Ogledov: 1061; Prenosov: 71
URL Povezava na celotno besedilo

10.
Iskanje izvedeno v 0.17 sek.
Na vrh
Logotipi partnerjev Univerza v Mariboru Univerza v Ljubljani Univerza na Primorskem Univerza v Novi Gorici